2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
RECOMMENDED CUTTING CONDITIONS
Cutting Cutting Width Depth of Cut Feed per Tooth (mm/tooth)
Speed
Work Material Grade Breaker vc (m/min) ae (mm) ap (mm) Cutting Edge Diameter D1
&25 &28 &32 &35 &40
&20 & 50 & 125
N <5 <0.05 <0.25 <0.4
<0.35
<0.25 D1 <10 <0.05 <0.2 <0.3
<0.4
<14.5 <0.05 <0.15 <0.35
<0.3
<5 <0.05 <0.25 <0.35
<0.3
<0.5 D1 <10 <0.2 <0.25
<0.35
Aluminium Alloy Si<5% TF15 GL 1000 <14.5 <0.15
(A6061, A7075) LC15TF (200 3000) <5 <0.05
<0.25
<0.4
<0.75 D1 <10 <0.2 <0.35
<0.3
<14.5 <0.15 <0.4
<0.35
<5 <0.05 <0.25 <0.3
<0.35
D1 <10 <0.3
<0.25
<14.5 <0.35
<5 <0.05 <0.35 <0.35 <0.4
<0.25 D1 <10 <0.05 <0.3 <0.3 <0.35 <0.1
<0.1
<14.5 <0.05 <0.25 <0.25 <0.3 <0.1
<0.1
<5 <0.05 <0.35 <0.35 <0.35 <0.1
<0.1
<0.5 D1 <10 <0.3 <0.3 <0.3 <0.05
Aluminium Alloy Si<5% TF15 GM 1000 <14.5 <0.2 <0.25 <0.25
(A6061, A7075) MP9120 (200 3000) <5 <0.05
<0.3 <0.3 <0.3
<0.75 D1 <10 <0.25 <0.25 <0.25
<14.5 <0.2 <0.2 <0.2
<5 <0.05 <0.25 <0.25 <0.3
D1 <10
<14.5
<5 <0.05 <0.35 <0.35 <0.4
<0.25 D1 <10 <0.05 <0.3 <0.3 <0.35
<14.5 <0.05 <0.25 <0.25 <0.3
Aluminium Alloy <5 <0.05 <0.35 <0.35 <0.35
(AC4B) <10
<0.5 D1 <14.5 <0.3 <0.3 <0.3
Aluminium Alloy <0.75 D1 <5
(ADC12, A390) 5%10% (200 3000) <14.5
<0.3 <0.3 <0.3
<0.25 <0.25 <0.25
<0.2 <0.2 <0.2
<5 <0.05 <0.25 <0.25 <0.3
D1 <10
<14.5
S <5 <0.05 <0.1
<0.25 D1 <10 <0.05 <0.1 ROTATING TOOLS
<14.5 <0.05 <0.1
<5 <0.05 <0.08 <0.1 <0.1
<0.5 D1 <10 <0.08 <0.1 <0.1
Titanium Alloy MP9120 GM 40 <14.5 <0.08 <0.1 <0.1
(Ti6Al4V) (30 60) <5 <0.05
<0.05 <0.08 <0.1
<0.75 D1 <10 <0.05 <0.08 <0.1
<14.5 <0.05 <0.08 <0.1
<5 <0.05 <0.05 <0.05 <0.05
D1 <10
<14.5
(Note 1) The above cutting conditions are determined based on high workpiece and machine rigidity, where no vibration occurred. If vibrations
occur make adjustments according to the machining conditions.
(Note 2) Note, vibrations may occur in the following conditions.
When using long tool overhang.
When pocket machining corner radii.
When the workpiece has poor clamping rigidity or when the machine rigidity or workpiece rigidity is low, vibrations can occur easily,
if so, reduce cutting conditions such as width and depth of cut and feed per tooth.
SPARE PARTS M001
TECHNICAL DATA
N001 K047
info@mitsubishitools.ru www.mitsubishitools.ru