2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
& 30 - 35 & 40 (& 32 Shank) & 40 (& 42 Shank) & 50/& 63 (Shank type) & 50/& 63 (Arbor type) & 80 - 160 (Arbor type)
Over- Axial Feed per Over- Axial Feed per Over- Axial Feed per Over- Axial Feed per Over- Axial Feed per Over- Axial Feed per
hang Depth Tooth hang Depth Tooth hang Depth Tooth hang Depth Tooth hang Depth Tooth hang Depth Tooth
(mm) of Cut (mm) of Cut (mm) of Cut (mm) of Cut (mm) of Cut (mm) of Cut
(mm) (mm/tooth) (mm) (mm/tooth) (mm) (mm/tooth) (mm) (mm/tooth) (mm) (mm/tooth) (mm) (mm/tooth)
180 1.2 1.2 180 1.2 1.2 180 1.2 1.3 180 1.4 1.3 150 1.5 1.3 170 1.5 1.3
230 1.0 1.0 240 1.0 1.0 240 1.0 1.1 240 1.2 1.1 250 1.3 1.1 300 1.3 1.1
290 0.8 0.8 300 0.8 0.8 300 0.8 0.9 350 1.1 0.9 450 1.0 0.8
180 1.2 1.2 180 1.2 1.2 180 1.2 1.3 180 1.4 1.3 150 1.5 1.3 170 1.5 1.3
230 1.0 1.0 240 1.0 1.0 240 1.0 1.1 240 1.2 1.1 250 1.3 1.1 300 1.3 1.1
290 0.8 0.8 300 0.8 0.8 300 0.8 0.9 350 1.1 0.9 450 1.0 0.8
180 1.2 1.6 180 1.2 1.6 180 1.2 1.7 180 1.4 1.7 150 1.5 1.7 170 1.5 1.7
230 1.0 1.4 240 1.0 1.4 240 1.0 1.5 240 1.2 1.5 250 1.3 1.5 300 1.3 1.5
290 0.8 1.2 300 0.8 1.2 300 0.8 1.3 350 1.1 1.3 450 1.0 1.2
180 1.0 1.4 180 1.0 1.4 180 1.0 1.5 180 1.2 1.5 150 1.3 1.5 170 1.3 1.5
230 0.8 1.2 240 0.8 1.2 240 0.8 1.3 240 1.0 1.3 250 1.1 1.3 300 1.1 1.3
290 0.6 1.0 300 0.6 1.0 300 0.6 1.1 350 0.9 1.1 450 0.8 1.0
180 0.6 1.0 180 0.6 1.0 180 0.6 1.1 180 0.8 1.1 150 0.9 1.1 170 0.9 1.1
230 0.5 0.8 240 0.5 0.8 240 0.5 0.9 240 0.6 0.9 250 0.7 0.9 300 0.7 0.9
290 0.4 0.6 300 0.4 0.6 300 0.4 0.7
NOTE FOR PROGRAMMING EFFECTIVE USE
When using , please
programme as an R3 radius cutter.
Uncut portion K The approximate uncut portions for
the programme are as follows.
R
1°30' Ls
ROTATING TOOLS
Insert Approx. R(mm) Uncut portion K(mm)
JOMo06T215ZZSR-oo 2.0 0.33
JOMo080320ZZSR-oo 2.5 0.46 The tapered body of the Vertical wall machining
special arbor for the is possible within the
JDMo09T320ZDSR-oo 3.0 0.47 enables machining without range of Ls.
touching a finished wall with
JDMo120420ZDSR-oo 3.0 0.63 a 1°30' draft angle.
JDMo140520ZDSR-oo 3.0 0.64
(Note) The uncut portion may change slightly depending on cutting
conditions.
info@mitsubishitools.ru www.mitsubishitools.ru K071TECHNICAL DATA N001
