2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
TURNING INSERTS
TURNING INSERTS RECOMMENDED CUTTING CONDITIONS
y 7° POSITIVE INSERT TYPE Breaker : Std : Standard Flat : Flat Top
Work Material Tensile Cutting Priority Breaker Grade Cutting Speed Feed Depth of Cut
K Strength Mode (m/min) (mm/rev) (mm)
MC5005
F1 MK UC5115 170 270 0.08 0.30 0.30 2.00
F2 Std MC5005 130 245 0.08 0.30 0.30 2.00
L1 MK UC5115 170 270 0.08 0.30 0.30 2.00
MC5005 130 245 0.08 0.30 0.30 2.00
Gray Cast Iron < 350MPa L2 Std UC5115 170 270 0.08 0.30 0.30 2.00
(GG30) M1 Flat MC5015 130 245 0.08 0.30 0.30 2.00
M2 Flat UC5115 155 245 0.08 0.30 0.30 2.00
F1 MK MC5015 130 245 0.08 0.30 0.30 2.00
F2 Std UC5115 155 245 0.08 0.30 0.30 2.00
L1 MK MC5015 130 245 0.08 0.30 0.30 2.00
L2 Std UC5115 155 245 0.08 0.30 0.30 2.00
MC5015 130 245 0.08 0.30 0.30 2.00
Ductile Cast Iron < 450MPa M1 Flat UC5115 155 245 0.08 0.30 0.30 2.00
(GGG40) M2 Flat MC5015 130 245 0.08 0.30 0.30 2.00
F1 MK UC5115 155 245 0.08 0.30 0.30 2.00
F2 Std MC5015 130 245 0.08 0.30 0.30 2.00
L1 MK UC5115 155 245 0.08 0.30 0.30 2.00
L2 Std MC5005 130 245 0.08 0.30 0.30 2.00
M1 Flat UC5115 160 255 0.08 0.30 0.30 2.00
M2 Flat MC5005 125 230 0.08 0.30 0.30 2.00
F1 MK UC5115 160 255 0.08 0.30 0.30 2.00
F2 Std MC5005 125 230 0.08 0.30 0.30 2.00
L1 MK UC5115 160 255 0.08 0.30 0.30 2.00
L2 Std MC5015 125 230 0.08 0.30 0.30 2.00
M1 Flat UC5115 145 235 0.08 0.30 0.30 2.00
M2 Flat MC5015 125 230 0.08 0.30 0.30 2.00
F1 MK UC5115 145 235 0.08 0.30 0.30 2.00
F2 Std MC5015 125 230 0.08 0.30 0.30 2.00
L1 MK UC5115 145 235 0.08 0.30 0.30 2.00
L2 Std MC5015 125 230 0.08 0.30 0.30 2.00
M1 Flat UC5115 140 225 0.08 0.30 0.30 2.00
M2 Flat MC5015 125 230 0.08 0.30 0.30 2.00
F1 MK UC5115 140 225 0.08 0.30 0.30 2.00
F2 Std MC5015 125 230 0.08 0.30 0.30 2.00
L1 MK UC5115 140 225 0.08 0.30 0.30 2.00
L2 Std MC5005 125 230 0.08 0.30 0.30 2.00
UC5115 140 225 0.08 0.30 0.30 2.00
Ductile Cast Iron < 800MPa M1 Flat MC5005 110 205 0.08 0.30 0.30 2.00
(GGG70) M2 Flat UC5115 140 225 0.08 0.30 0.30 2.00
F1 MK MC5005 110 205 0.08 0.30 0.30 2.00
F2 Std UC5115 140 225 0.08 0.30 0.30 2.00
L1 MK MC5015 110 205 0.08 0.30 0.30 2.00
L2 Std UC5115 130 205 0.08 0.30 0.30 2.00
M1 Flat MC5015 110 205 0.08 0.30 0.30 2.00
M2 Flat UC5115 130 205 0.08 0.30 0.30 2.00
F1 MK MC5015 110 205 0.08 0.30 0.30 2.00
F2 Std 130 205 0.08 0.30 0.30 2.00
L1 MK
L2 Std
M1 Flat
CUTTING CONDITIONS : : Stable Cutting : General Cutting : Unstable Cutting
CUTTING AREA : F : Finish Cutting : Light Cutting M : Medium Cutting R : Rough Cutting H : Heavy Cutting
A086 info@mitsubishitools.ru www.mitsubishitools.ru