2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
CARBIDE для заказа - info@mitsubishitools.ru
DRILLING (SOLID CARBIDE)
MMS
RECOMMENDED CUTTING CONDITIONS
Work Austenitic Stainless Steel ( < 200HB) Austenitic Stainless Steel (>200HB)
Material X5CrNi1810, X5CrNiMo17-12-2
X2CrNiN1810, X2CrNiMoN17-12-2
Drill Dia. Cutting Speed Revolution Feed rate Table Feed Cutting Speed Revolution Feed rate Table Feed
(min-1) (Min. Max.) (min-1) (Min. Max.) (mm/min)
(mm) (m/min) (mm/min) (m/min)
(mm/rev) (mm/rev) 590
3.2 80 7900 1025 60 5900 560
4.0 80 6300 0.13 (0.08 0.18) 0.1 (0.05 0.15) 455
5.0 80 5000 0.15 (0.10 0.20) 945 60 4700 0.12 (0.08 0.18) 450
6.3 80 4000 0.15 (0.10 0.20) 0.12 (0.08 0.18) 390
8.0 80 3100 0.17 (0.12 0.22) 750 60 3800 0.15 (0.1 0.2) 270
10.0 60 1900 0.19 (0.14 0.24) 0.17 (0.12 0.22) 245
12.0 60 1500 0.2 (0.15 0.25) 680 60 3000 0.18 (0.13 0.23) 180
16.0 60 1100 0.21 (0.16 0.26) 0.19 (0.14 0.24) 145
20.0 60 0.22 (0.17 0.27) 585 60 2300 0.2 (0.15 0.25)
900 0.23 (0.18 0.28) 0.21 (0.16 0.26)
380 50 1500
315 50 1300
240 50 900
205 50 700
Two-phase Stainless Steel ( < 280HB) Ferritic and Martensitic Stainless Steel ( < 200HB)
X3CrNiMoN27-5-2
Work X10Cr13, X6Cr17
Material
Drill Dia. Cutting Speed Revolution Feed rate Table Feed Cutting Speed Revolution Feed rate Table Feed
(min-1) (Min. Max.) (min-1) (Min. Max.) (mm/min)
(mm) (m/min) (mm/min) (m/min)
(mm/rev) (mm/rev) 1025
3.2 50 4900 490 80 7900 945
4.0 50 3900 0.1 (0.05 0.15) 0.13 (0.08 0.18) 750
5.0 50 3100 0.12 (0.08 0.18) 465 80 6300 0.15 (0.10 0.20) 680
6.3 50 2500 0.12 (0.08 0.18) 0.15 (0.10 0.20) 585
8.0 50 1900 0.15 (0.1 0.2) 370 80 5000 0.17 (0.12 0.22) 380
10.0 40 1200 0.17 (0.12 0.22) 0.19 (0.14 0.24) 315
12.0 40 1000 0.18 (0.13 0.23) 375 80 4000 0.2 (0.15 0.25) 240
16.0 40 0.19 (0.14 0.24) 0.21 (0.16 0.26) 205
20.0 40 700 0.2 (0.15 0.25) 320 80 3100 0.22 (0.17 0.27)
600 0.21 (0.16 0.26) 0.23 (0.18 0.28)
215 60 1900
190 60 1500
140 60 1100
125 60 900
DRILLING Work Ferritic and Martensitic Stainless Steel (>200HB) Hardened Stainless Steel (<450HB)
Material
X20CrNi17-2, X30Cr13 X5CrNiCuNb164, X7CrNiAl177, 17-4PH, 17-7PH
Drill Dia. Cutting Speed Revolution Feed rate Table Feed Cutting Speed Revolution Feed rate Table Feed
(min-1) (Min. Max.) (min-1) (Min. Max.) (mm/min)
(mm) (m/min) (mm/min) (m/min)
(mm/rev) (mm/rev) 490
465
3.2 60 5900 0.1 (0.05 0.15) 590 50 4900 0.1 (0.05 0.15) 370
4.0 60 4700 0.12 (0.08 0.18) 0.12 (0.08 0.18) 375
5.0 60 3800 0.12 (0.08 0.18) 560 50 3900 0.12 (0.08 0.18) 320
6.3 60 3000 0.15 (0.1 0.2) 0.15 (0.1 0.2) 215
8.0 60 2300 0.17 (0.12 0.22) 455 50 3100 0.17 (0.12 0.22) 190
10.0 50 1500 0.18 (0.13 0.23) 0.18 (0.13 0.23) 140
12.0 50 1300 0.19 (0.14 0.24) 450 50 2500 0.19 (0.14 0.24) 125
16.0 50 0.2 (0.15 0.25) 0.2 (0.15 0.25)
20.0 50 900 0.21 (0.16 0.26) 390 50 1900 0.21 (0.16 0.26)
700
270 40 1200
245 40 1000
180 40 700
145 40 600
(Note 1) Using a high pressure, through spindle coolant system is recommended.
(Note 2) Emulsion type water based coolant is recommended.
(Note 3) When using non-water coolant, reduce the revolution by 10% 20%.
L070 info@mitsubishitools.ru www.mitsubishitools.ru