2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
DRILLING (INDEXABLE TYPE)
STAW a W avy cutting edge design for good chip control. CARBIDE
a H ighly rigid clamping system offers stability and reliability for small hole drilling.
Carbon Steel Hardened Stainless Cast Iron Light Alloy Heat Resistant
Alloy Steel Steel Steel Alloy
e
e u u
Stock L3
D1 L2
140°
L1
VP15TF
y HOLDERS DP5010
Holder D4
Drill Dia. Hole Depth Order Number Drill Insert Stock Dimensions (mm)
Range Dia. Order Number L3 L2 L1 D4
D1
D1 (mm) Wrench
(mm) (l/d) TIP06F
TIP06F
1.5 STAWSS1000S16 a 10.0 STAWN1000TH a 16 TIP06F DRILLING
10.0 3 STAWSN1000S16 STAWK1000TG 16 TIP06F
10.4 5 STAWMN1000S16 10.1 STAWN1010TH a 22 32 80 16 TIP06F
STAWLN1000S16 STAWK1010TG 16 TIP06F
8 STAWSS1050S16 a STAWN1020TH a 16 TIP06F
1.5 STAWSN1050S16 STAWK1020TG 16 TIP06F
10.5 3 STAWMN1050S16 10.2 STAWN1030TH a 37 47 95 16 TIP06F
10.9 5 STAWLN1050S16 STAWK1030TG 16 TIP06F
8 STAWSS1100S16 a STAWN1040TH a 16 TIP06F
1.5 STAWSN1100S16 STAWK1040TG 16 TIP06F
11.0 3 STAWMN1100S16 10.3 STAWN1050TH a 16 TIP06F
11.4 5 STAWLN1100S16 STAWK1050TG 16 TIP06F
8 STAWSS1150S16 a 10.4 STAWN1060TH a 57 67 115 16 TIP06F
1.5 STAWSN1150S16 STAWK1060TG 16 TIP06F
11.5 3 STAWMN1150S16 a 10.5 STAWN1070TH a 16 TIP06F
11.9 5 STAWLN1150S16 STAWK1070TG 16 TIP06F
8 STAWSS1200S16 10.6 STAWN1080TH a 87 97 145 16 TIP06F
1.5 STAWSN1200S16 STAWK1080TG 16 TIP06F
12.0 3 STAWMN1200S16 a STAWN1090TH a 16
12.4 5 STAWLN1200S16 STAWK1090TG 16
8 10.7 STAWN1100TH a
STAWK1100TG
a STAWN1110TH a 22 32 80
STAWK1110TG
10.8 STAWN1120TH a
STAWK1120TG
a 10.9 STAWN1130TH a 37 47 95
STAWK1130TG
a 11.0 STAWN1140TH a
STAWK1140TG
11.1 STAWN1150TH a
STAWK1150TG
a STAWN1160TH a 57 67 115
STAWK1160TG
11.2 STAWN1170TH a
STAWK1170TG
a STAWN1180TH a 87 97 145
STAWK1180TG
11.3 STAWN1190TH a
STAWK1190TG
a 11.4 STAWN1200TH a
STAWK1200TG
a 11.5 STAWN1210TH a 25 36 84
STAWK1210TG
11.6 STAWN1220TH a
STAWK1220TG
a STAWN1230TH a 41 52 100
STAWK1230TG
11.7 STAWN1240TH a
STAWK1240TG
a a
11.8 a 66 77 125
a 11.9 a
a 12.0 a 96 107 155
12.1 a
a a
12.2 a 25 36 84
a a
12.3 a 41 52 100
a 12.4 a
a
a 66 77 125
a
a 96 107 155
a
a
a 27 39 87
a
a 45 57 105
a
a
a 70 82 130
a
a 105 117 165
a
(Note 1) The above dimensions are for when installing the STAWN (VP15TF) insert.
(Note 2) Please contact us for any geometry that is not in this catalogue (e.g. different diameter and length).
a : Inventory maintained. (Note: 1 insert in one case) INSERT DESCRIPTION L118 L115
info@mitsubishitools.ru CUTTING CONDITIONS L122
USAGE NOTE L123
TECHNICAL DATA N001
www.mitsubishitools.ru