2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN

                                                                         для заказа - info@mitsubishitools.ru

      EXTERNAL TURNING TOOLS

      XC ooINSERTS
                TOOL HOLDERS
      SXZC
                                                 External turning, Copying                                                                                                        Profile Holder Finish
                                                                                                                                                                                                                     SVX

                            < 300°

EXTERNAL TURNING                                                                                                                                                                                                     (15)
                                                                                                                        H2 F1
                                                                                                                                                               H12°92°30L1
                                                                                                                                                                                             BL2
      92°
      30

                                                                                                                                                                          Right hand tool holder shown.

                            Stock                                   Dimensions (mm)                                                                                    *                        *
                            RL
      Order Number                               Insert Number

                                                                H1      B   L1  L2 H2 F1                                                                           Clamp  Clamp   Clamp Bridge     Spring   Insert Wrench
                                                                                                                                                                   Screw  Bridge      Screw                Wrench (Clamp bridge)

      SXZCR/L1616H15 a a                         1503oo-SVX 16 16 100 35 16 20 TS255 AMS3 AJS3010T10 ASS2 TKY08F TKY10F

            2020K15 a a XCMT 1503oo-SVX 20 20 125 35 20 25 TS255 AMS3 AJS3010T10 ASS2 TKY08F TKY10F

            2525M15 a a                          1503oo-SVX 25 25 150 40 25 32 TS255 AMS3 AJS3010T10 ASS2 TKF08F TKF10F

      * Clamp Torque (N • m) : TS255=1.0, AJS3010T10=2.5

      NOTE

                         Notes when end face copying                                                                                                                             Not possible

      Pay special attention to the following when face copying.                                                                                                        Machining of V-pulleys

      Depth from end face                        aMachining of an outer diameter (Step z)                                                                                                 When machining V-pulleys,
      Up to 10mm                                                                                                                                                                          use a VNMG insert.
                                                 •	T o prevent burr formation, the depth of cut should be
                              Inclination angle   below half the nose radius.
                              60 or less

                                                 aMachining of an inclination (Step x)

                    2                            •	T o reduce the contact length of chips, the depth of
                         1                        cut should be below half the nose radius.
                                                 •	T o prevent interference between the tool and the
                                                  workpiece, the cutting diameter should be 40mm or
                                                  larger, inclination angle 60° or less and depth from
                                                  the end face up to 10mm.
      Cutting Diameter > &40mm
                                                                                                                                                  Depth of Cut (mm)aWhen changing inserts

                                                 •	W hen indexing the inserts, it is recommended to preset
                                                  the cutting edge position to maintain machining accuracy.

      RECOMMENDED CUTTING CONDITIONS                                                                                                                               y APPLICABLE RANGE

      Work Material         Hardness             Grade   Cutting Speed                                                                                                   0.8
                                                             (m/min)                                                                                                     0.7
                                                                                                                                                                         0.6
      P Mild Steel          < 180HB              UE6020  150  350
                                                                                                                                                                       0.5 Corner R0.8
      Carbon Steel, Alloy Steel 150HB  250HB    UE6020  100  250
                                                                                                                                                                         0.4
      M Stainless Steel     < 200HB              VP15TF  100 (70  120)
                                                                                                                                                                                        Corner R0.4
      (Note) The above cutting conditions are general guidelines.
               Adjustments maybe necessary depending on machine rigidity,                                                                                                0.3
               workpiece geometry and clamping.                                                                                                                          0.2

                                                                                                                                                                            Corner R0.2

                                                                                                                                                                         0.1
                                                                                                                                                                            0 0.1	 0.2	 0.3
                                                                                                                                                                                                            Feed (mm/rev)

      (Note) Insert photo, letters show chip breaker style, figures show insert dimensions.

      a : Inventory maintained.

C032                                                                                                                                                                                            SXZC type inserts A160

                                                 info@mitsubishitools.ru        www.mitsubishitools.ru