2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
FSVJB/C VCooinserts, VBooinserts Finish Finish Light Light
FP FM LP LM
142° 142°
(11) (11) (11) (11)
Medium
MV
RR° Re F1L3 H1 Finish
D1 BORINGD4
L1 FV
5°
Right hand tool holder shown. (08,11) (08,11)
Stock Dimensions (mm) Min. Standard Maximum *
Cutting Corner Recom-
Order Number Insert Number Diameter Radius mendation
l/d
RL D4 L1 L3 F1 H1 RR° D1 Re Ratio Clamp Wrench
Screw
FSVJC1612R/L-08S a a VCGT 0802oo 12 150 26 2 11 5 16 0.4 4 TS202 TKY06F
2016R/L-08S a a VCMT 0802oo
16 180 36 2 15 5 20 0.4 5 TS202 TKY06F
FSVJB2520R/L-11S a a VBET 1103oo 20 200 37.5 2 19 5 25 0.4 5 TS255 TKY08F
3025R/L-11S a a VBGT 1103oo
VBMT 25 250 45 3.5 23.4 5 30 0.4 5 TS255 TKY08F
* Clamp Torque (N • m) : TS202=0.6, TS255=1.0
RECOMMENDED CUTTING CONDITIONS
Work Material Cutting Breaker Recom- Grade Cutting Speed l/d < 3 (Steel shank) l/d = 4 5 (Steel shank)
Mode mendation (m/min) l/d < 6 (Carbide shank) l/d = 7 8 (Carbide shank)
Feed Depth of Cut Feed Depth of Cut
(mm/rev) (mm) (mm/rev) (mm)
P Finish FV z NX2525 170 (120 220) 0.10 (0.05 0.15) 0.5 0.10 (0.05 0.15) 0.5
Mild Steel Light SV z NX3035 150 (100 200) 0.20 (0.10 0.25) 1.0
x NX2525 160 (110 210) 0.20 (0.10 0.25) 1.0 0.15 (0.05 0.20) 1.0
< 180HB z NX3035 140 (90 190) 0.25 (0.15 0.35) 2.0
x NX2525 150 (100 200) 0.25 (0.15 0.35) 2.0 0.15 (0.05 0.20) 1.0
Medium MV 0.20 (0.15 0.25) 1.5
0.20 (0.15 0.25) 1.5
Finish FV z VP15TF 140 (90 190) 0.10 (0.05 0.15) 0.5 0.10 (0.05 0.15) 0.5
Light SV x NX2525 130 (80 180) 0.10 (0.05 0.15) 0.5
Medium MV z UE6020 140 (90 190) 0.20 (0.10 0.25) 1.0 0.10 (0.05 0.15) 0.5
x NX3035 110 (60 160) 0.20 (0.10 0.25) 1.0
Carbon Steel z UE6020 130 (80 180) 0.25 (0.15 0.35) 2.0 0.15 (0.05 0.20) 1.0
Alloy Steel x NX3035 100 (60 150) 0.25 (0.15 0.35) 2.0
180350HB 0.15 (0.05 0.20) 1.0
0.20 (0.15 0.25) 1.5
0.20 (0.15 0.25) 1.5
M Finish FV z VP15TF 150 (110 190) 0.10 (0.05 0.15) 0.5 0.10 (0.05 0.15) 0.5
1.0
Light SV z US735 125 (85 165) 0.20 (0.10 0.25) 1.0 0.15 (0.05 0.20) 1.0
Medium MV x VP15TF 130 (90 170) 0.20 (0.10 0.25) 2.0
Stainless Steel z US735 105 (70 135) 0.20 (0.15 0.25) 2.0 0.15 (0.05 0.20) 1.0
< 200HB x VP15TF 120 (80 160) 0.20 (0.15 0.25) 0.5
2.0
0.5 0.20 (0.15 0.25) 1.0
2.0
0.20 (0.15 0.25) 1.0
K Cast Iron Finish F, FS z HTi10 130 (90 160) 0.15 (0.10 0.20) 0.15 (0.10 0.20) 0.5
Tensile Strength Medium MV z VP15TF 90 (60 120) 0.20 (0.15 0.25)
< 350MPa 0.20 (0.15 0.25) 1.5
N Aluminium Alloy Finish F, FS z HTi10 300 (200 400) 0.10 (0.05 0.15) 0.10 (0.05 0.15) 0.5
z MD220 200 (150 250) 0.10 (0.05 0.15)
Flat Top 0.10 (0.05 0.15) 1.0
H Heat Treated Steel 3565HRC Finish Flat Top z MB825 100 (80 200) 0.10 (0.05 0.15) 0.15 0.10 (0.05 0.15) 0.1
(Note 1) When vibrations occur, reduce cutting speed by 30%.
(Note 2) The depth of cut needs to be less than the nose diameter when using the FSVJ type.
VBoo type inserts A150 A152 E013
VCoo type inserts A153, A154
CBN & PCDinserts B041, B055
SPARE PARTS M001
TECHNICAL DATA N001
info@mitsubishitools.ru www.mitsubishitools.ru