2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
SCLC CC insertsoo Finish Finish Light Light
FP FM LP LM
95° 60° (06,09) (06,09) (06,09) (06,09)
95°
F1 F1 Medium Medium Flat Top PCD/CBN
BORING
Re L3 MP MM
H1
RR°
D1 L1 D4
Stock Right hand tool holder shown. (06,09,12) (06,09,12) (06,09,12) (06,09,12)
Min. Standard
Dimensions (mm) *
Cutting Corner
Order Number Insert Number Diameter Radius
R L D4 L1 L3 F1 H1 RR° D1 Re Clamp Screw Wrench
S08FSCLCR/L06 a a 0602oo 8 80 12 6 7 15 11 0.4 TS25 TKY08F
S10HSCLCR/L06 a a CCMH 0602oo 10 100 16 7 9 13 13 0.4 TS25 TKY08F
CCMT TS25 TKY08F
S12KSCLCR/L06 aa 0602oo 12 125 20 9 11 10 16 0.4 TS4 TKY15F
TS4 TKY15F
S16MSCLCR/L09 a a CCET 09T3oo 16 150 25 11 14 7 20 0.8 TS5 TKY25F
S20QSCLCR/L09 a a CCGT 09T3oo 20 180 32 13 18 7 25 0.8 TS5 TKY25F
CCMW
S25RSCLCR/L12 a a CCGW 1204oo 25 200 40 17 23 5 32 0.8
NP-CCGW
S32SSCLCR/L12 a a 1204oo 32 250 50 22 30 5 40 0.8
S40TSCLCR/L12 a a 1204oo 40 300 63 27 37 5 50 0.8 TS5 TKY25F
* Clamp Torque (N • m) : TS25=1.0, TS4=3.5, TS5=7.5
SCLC
Carbide shank CCooinserts Finish Finish Light Light
FP FM LP LM
95° 60° (06,09) (06,09) (06,09) (06,09)
95°
Medium Medium Flat Top PCD/CBN
Re L3 MP MM
H1
RR°
D1 L1 D4
Stock Right hand tool holder only. (06,09,12) (06,09,12) (06,09,12) (06,09,12)
Min. Standard
Dimensions (mm) *
Cutting Corner
Order Number Insert Number Diameter Radius
R D4 L1 L3 F1 H1 RR° D1 Re Clamp Screw Wrench
C08HSCLCR06 a CCMH 0602oo 8 100 12 6 7 15 11 0.4 TS25 TKY08F
C10KSCLCR06 TS25 TKY08F
C12MSCLCR06 a CCMT 0602oo 10 125 16 7 9 13 13 0.4 TS25 TKY08F
C16RSCLCR09 CCET TS4 TKY15F
C20SSCLCR09 TS4 TKY15F
a CCGT 0602oo 12 150 20 9 11 10 16 0.4
a CCMW 09T3oo 16 200 25 11 14 7 20 0.8
CCGW
a NP-CCGW 09T3oo 20 250 32 13 18 7 25 0.8
* Clamp Torque (N • m) : TS25=1.0, TS4=3.5
RECOMMENDED CUTTING CONDITIONS
Steel Shank l/d < 3 l/d=3 4 (Shank Diameter > 25mm)
Carbide Shank l/d < 5 l/d=6 7
Work Material Hardness Cutting Mode Cutting Speed Feed Depth of Cut Cutting Speed Feed Depth of Cut
P Carbon Steel Light Cutting (m/min) (mm/rev) (mm) (m/min) (mm/rev) (mm)
Alloy Steel 180 350HB 130 (90 160) 0.1 (0.05 0.15) 0.2 120 (80 150) 0.1 (0.05 0.15) 0.2
Medium Cutting 90 (60 120) 80 (50 110)
0.25 (0.15 0.35) 3.0 0.15 (0.1 0.2) 1.5
M Light Cutting 140 (100 180) 0.1 (0.05 0.15) 0.2 140 (100 180) 0.1 (0.05 0.15) 0.2
Stainless Steel < 200HB 0.2 (0.15 0.25) 2.0 60 (40 80) 0.15 (0.1 0.2) 1.0
Medium Cutting 70 (50 90)
N Light Cutting 300 (200 400) 0.1 (0.05 0.15) 0.2 300 (200 400) 0.1 (0.05 0.15) 0.2
Aluminium Alloy
Medium Cutting 200 (150 250) 0.1 (0.05 0.15) 2.0 200 (150 250) 0.1 (0.05 0.15) 1.5
CCoo type inserts A127 A132 SPARE PARTS M001
TECHNICAL DATA
CBN & PCD inserts B034, B035, B051 N001 E031
info@mitsubishitools.ru www.mitsubishitools.ru