2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
GROOVING SYSTEM
GYSERIES (FACE GROOVING)
4 00° type holder
(Note 1) For modular blades and modular holders, please order separately.
(Note 2) P lease use right hand modular blade for right hand modular holder.
Insert GY2Mooooooooo--GGSM Insert GY2Gooooooooo-MF
Insert GY2Mooooooooo-GU Insert GY2Mooooooooo-MS
Insert GY1Gooooooooo- GF Insert GY2Mooooooooo-MM ar
GS
GROOVING L1
H2 F1
W3Insert GY2Mooooooooo-BM&D1 Fig. 1L2L2
H1
H2Fig. 2
B
H1
Right hand tool holder shown.
Seat Insert Hand First Cut Diameter Max. Order Number
Size Width (R/L) D1 (mm) Groove Depth
ID
W3 Min. Max. ar
(mm) (mm) Modular Blade Stock Modular Holder Stock
35 40 12 (4Q1R4F11) GYM25RD-F12-035 a
40 50 12 (4Q1R4F12) GYM25RD-F12-040 a
50 60 12 (4Q1R4F13) GYM25RD-F12-050 a
12 (4Q1R4F14) GYM25RD-F12-060
60 75 a
*20 1 (4Q1R4F24) GYM25RD-F20-060 a
75 100 a GYHR3225P00-M25R a
12 (4Q1R4F15) GYM25RD-F12-075 a
100 150 a
*20 1 (4Q1R4F25) GYM25RD-F20-075 a
135 200 a
12 (4Q1R4F16) GYM25RD-F12-100 a
180 250 a
*20 1 (4Q1R4F26) GYM25RD-F20-100 a
*3.00 3 225 999 a
12 (4Q1R4F17) GYM25RD-F12-135 a
F 3.18 R
*20 1 (4Q1R4F27) GYM25RD-F20-135 a
3.24 35 40
12 (4Q1R4F18) GYM25RD-F12-180
*20 1 (4Q1R4F28) GYM25RD-F20-180
12 (4Q1R4F19) GYM25RD-F12-225
*20 1 (4Q1R4F29) GYM25RD-F20-225
12 (4J1R4F11) GYM25RD-F12-035
40 50 12 (4J1R4F12) GYM25RD-F12-040 a
50 60 12 (4J1R4F13) GYM25RD-F12-050 a
60 75 12 (4J1R4F14) GYM25RD-F12-060 a GYHR3232P00-M25R a
75 100 GYM25RD-F20-060 a
100 150 *20 1 (4J1R4F24) GYM25RD-F12-075 a
135 200 GYM25RD-F20-075 a
180 250 12 (4J1R4F15) GYM25RD-F12-100 a
225 999 GYM25RD-F20-100 a
*20 1 (4J1R4F25) GYM25RD-F12-135 a
GYM25RD-F20-135 a
12 (4J1R4F16) GYM25RD-F12-180 a
GYM25RD-F20-180 a
*20 1 (4J1R4F26) GYM25RD-F12-225 a
GYM25RD-F20-225 a
12 (4J1R4F17)
*20 1 (4J1R4F27)
12 (4J1R4F18)
*20 1 (4J1R4F28)
12 (4J1R4F19)
*20 1 (4J1R4F29)
1 The maximum groove depth varies according to the insert used. Please refer to the maximum groove depth of inserts on pages F014 F016.
*2 Dimensions shown are when the gauge insert is used. If other insert geometries are used then L1, L2, F1 and D1 values may vary.
**3 Refer to page F070 for left hand tools.
Notes when selecting a modular blade (1)
a Select a modular blade for face grooving, so that the cutting diameter at &D1 (Min.)
the first pass is within the range of D1 minimum and D1 maximum that &D1 (Max.)
are described in the table of dimensions.
a : Inventory maintained.
F066 info@mitsubishitools.ru www.mitsubishitools.ru