2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
GROOVING SYSTEM
GYSERIES (FACE GROOVING)
4 00° type holder
(Note 1) For modular blades and modular holders, please order separately.
(Note 2) P lease use left hand modular blade for left hand modular holder.
Insert GY2Mooooooooo--GGSM Insert GY2Gooooooooo-MF
Insert GY2Mooooooooo-GU Insert GY2Mooooooooo-MS
Insert GY1Gooooooooo- GF Insert GY2Mooooooooo-MM ar
GS
GROOVINGInsert GY2Mooooooooo-BM L2 L1 L2
H1Fig. 2
H2 BFig. 1
H1
H2 W3Left hand tool holder shown.
&D1 F1
Seat Insert Hand First Cut Diameter Max. Order Number
Size Width (R/L) D1 (mm) Groove Depth
ID
W3 Min. Max. ar
(mm) (mm) Modular Blade Stock Modular Holder Stock
35 40 12 (4Q1L4F11) GYM25LD-F12-035 a
40 50 12 (4Q1L4F12) GYM25LD-F12-040 a
50 60 12 (4Q1L4F13) GYM25LD-F12-050 a
12 (4Q1L4F14) GYM25LD-F12-060
60 75 a
*20 1 (4Q1L4F24) GYM25LD-F20-060 a
75 100 a GYHL3225P00-M25L a
12 (4Q1L4F15) GYM25LD-F12-075 a
100 150 a
*20 1 (4Q1L4F25) GYM25LD-F20-075 a
135 200 a
12 (4Q1L4F16) GYM25LD-F12-100 a
180 250 a
*20 1 (4Q1L4F26) GYM25LD-F20-100 a
*3.00 3 225 999 a
12 (4Q1L4F17) GYM25LD-F12-135 a
F 3.18 L
*20 1 (4Q1L4F27) GYM25LD-F20-135 a
3.24 35 40
12 (4Q1L4F18) GYM25LD-F12-180 a
40 50
*20 1 (4Q1L4F28) GYM25LD-F20-180
12 (4Q1L4F19) GYM25LD-F12-225
*20 1 (4Q1L4F20) GYM25LD-F20-225
12 (4J1L4F11) GYM25LD-F12-035
12 (4J1L4F12) GYM25LD-F12-040
50 60 12 (4J1L4F13) GYM25LD-F12-050 a
60 75 12 (4J1L4F14) GYM25LD-F12-060 a GYHL3232P00-M25L a
75 100 GYM25LD-F20-060 a
100 150 *20 1 (4J1L4F24) GYM25LD-F12-075 a
135 200 GYM25LD-F20-075 a
180 250 12 (4J1L4F15) GYM25LD-F12-100 a
225 999 GYM25LD-F20-100 a
*20 1 (4J1L4F25) GYM25LD-F12-135 a
GYM25LD-F20-135 a
12 (4J1L4F16) GYM25LD-F12-180 a
GYM25LD-F20-180 a
*20 1 (4J1L4F26) GYM25LD-F12-225 a
GYM25LD-F20-225 a
12 (4J1L4F17)
*20 1 (4J1L4F27)
12 (4J1L4F18)
*20 1 (4J1L4F28)
12 (4J1L4F19)
*20 1 (4J1L4F20)
1 The maximum groove depth varies according to the insert used. Please refer to the maximum groove depth of inserts on pages F014 F016.
*2 Dimensions shown are when the gauge insert is used. If other insert geometries are used then L1, L2, F1 and D1 values may vary.
**3 Refer to page F066 for right hand tools.
Notes when selecting a modular blade (1)
a Select a modular blade for face grooving, so that the cutting diameter at &D1 (Min.)
the first pass is within the range of D1 minimum and D1 maximum that &D1 (Max.)
are described in the table of dimensions.
a : Inventory maintained.
F070 info@mitsubishitools.ru www.mitsubishitools.ru