2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
GROOVING SYSTEM
GYSERIES (FACE GROOVING)
4 00° type holder
(Note 1) For modular blades and modular holders, please order separately.
(Note 2) P lease use left hand modular blade for left hand modular holder.
Insert GY2Mooooooooo--GGSM Insert GY2Gooooooooo-MF
Insert GY2Mooooooooo-GU Insert GY2Mooooooooo-MS
Insert GY1Gooooooooo- GF Insert GY2Mooooooooo-MM ar
GS
GROOVING L1
H1
BInsert GY2Mooooooooo-BML2L2
H2Fig. 2
H1Fig. 1
H2 W3
&D1 F1Left hand tool holder shown.
Seat Insert Hand First Cut Diameter Max. Order Number
Size Width (R/L) D1 (mm) Groove Depth
ID
W3 Min. Max. ar
(mm) (mm) Modular Blade Stock Modular Holder Stock
50 60 14 (4E1L4H11) GYM25LD-H14-050 a GYHL2020K00-M25L a
60 85 14 (4E1L4H12) GYM25LD-H14-060
85 125 a
125 200 *25 1 (4E1L4H22) GYM25LD-H25-060 a
180 280 a
250 999 14 (4E1L4H13) GYM25LD-H14-085 a
a
*25 1 (4E1L4H23) GYM25LD-H25-085 a
a
14 (4E1L4H14) GYM25LD-H14-125 a
a
*25 1 (4E1L4H24) GYM25LD-H25-125 a
14 (4E1L4H15) GYM25LD-H14-180
*25 1 (4E1L4H25) GYM25LD-H25-180
14 (4E1L4H16) GYM25LD-H14-250
*25 1 (4E1L4H26) GYM25LD-H25-250
*4.75 3
H 5.00 L 14 (4G1L4H11) GYM25LD-H14-050
14 (4G1L4H12) GYM25LD-H14-060
5.24 50 60 a
85 *25 1 (4G1L4H22) GYM25LD-H25-060
60 a
14 (4G1L4H13) GYM25LD-H14-085 a
85 125 a
*25 1 (4G1L4H23) GYM25LD-H25-085 a
a GYHL2525M00-M25L a
14 (4G1L4H14) GYM25LD-H14-125 a
125 200 a
*25 1 (4G1L4H24) GYM25LD-H25-125 a
180 280 a
14 (4G1L4H15) GYM25LD-H14-180 a
250 999
*25 1 (4G1L4H25) GYM25LD-H25-180
14 (4G1L4H16) GYM25LD-H14-250
*25 1 (4G1L4H26) GYM25LD-H25-250
1 The maximum groove depth varies according to the insert used. Please refer to the maximum groove depth of inserts on pages F014 F016.
*2 Dimensions shown are when the gauge insert is used. If other insert geometries are used then L1, L2, F1 and D1 values may vary.
**3 Refer to page F080 for right hand tools.
Notes when selecting a modular blade (1) &D1 (Min.)
&D1 (Max.)
a Select a modular blade for face grooving, so that the cutting diameter at
the first pass is within the range of D1 minimum and D1 maximum that
are described in the table of dimensions.
a : Inventory maintained.
F084 info@mitsubishitools.ru www.mitsubishitools.ru