2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
LIMITATION OF THE MAXIMUM GROOVE DEPTH Due to interference of this part,
the maximum groove depth is
When using the mono block type limited by the cutting diameter.
The maximum groove depth is not limited by the cutting diameter.
When using the modular blade type
The maximum groove depth is limited by the cutting diameter.
Max. Groove Depth (mm) •Shank Diameter=32mm (GYM20 Blade) Max. Groove Depth (mm) •Shank Diameter=40mm (GYM20 Blade)
12 12
11.5 11.5
11 GYM20L/RA-G12 11 GYM20L/RA-G12
10 GYM20L/RA-H12 10 GYM20L/RA-H12
9 9
8 GYM20L/RA-D10 8 GYM20L/RA-D10
GYM20L/RA-E10 7 GYM20L/RA-E10
7 6 GYM20L/RA-F10
5.5
6 GYM20L/RA-F10 5
5
4.5
4
40 44 55 65 80 90 105 y 50 56 65 80 100 110 130 y
41 48 54
Workpiece Diameter (mm) Workpiece Diameter (mm)
Max. Groove Depth (mm) • Shank Diameter=40mm (GYM25 Blade) Max. Groove Depth (mm) • Shank Diameter=50mm (GYM25 Blade) GROOVING
14 14
13 GYM25L/RA-G14 13 GYM25L/RA-G14
GYM25L/RA-H14 GYM25L/RA-H14
12 GYM25L/RA-J14 12 GYM25L/RA-J14
11.5 11.5
11 11
10 10
9 GYM25L/RA-D12 9 GYM25L/RA-D12
GYM25L/RA-E12 GYM25L/RA-E12
8 GYM25L/RA-F12 8 GYM25L/RA-F12
7.5 7.5
7 7
60 69 80 95 125 135 y 70 80 95 100 115 125 160 y
62 Workpiece Diameter (mm)
75 85 Workpiece Diameter (mm)
RECOMMENDED CUTTING SPEED (m/min)
Work Material Hardness Grade 50 100 Cutting Speed (m/min) 250 300
80 150 200
P < 160HB VP20RT 90 180 F119
< 160HB VP10RT
Mild Steel MNXY2550215 70 190
Mild Steel
170
VNPX2205R25T 60 140
Carbon Steel 160280HB VVPP210RRTT 70 150 210
160280HB VMPY1500R1T5 90 210
Alloy Steel MNXY2550215
Carbon Steel 280HB< VNPX2205R25T 55 135
280HB< VVPP210RRTT 50 110
Alloy Steel VMPY1500R1T5
< 270HB MNXY2550215 60 120
M < 270HB VNPX2205R25T 80 160
VVPP210RRTT
Stainless Steel Tensile Strength VVPP2100RRTT 45 105
< 300MPa VVPP210RRTT 50 110
M VMPY1500R1T5 60 120
Tensile Strength VMPY2500R15T 60 140
Stainless Steel < 300MPa VVPP210RRTT 70 150
VMPY1500R1T5 90
K Tensile Strength VMPY2500R15T 50 110
< 800MPa VVPP210RRTT 60 120
K Gray Cast Iron VRPT1900R10T 80 160
Tensile Strength MB8025
Gray Cast Iron < 800MPa 30 60
40 70
Ductile Cast Iron 40 70
60 100
Ductile Cast Iron
50HRC<
S
S Heat Resistant Alloy
HeaTtitRaneisuimstaAnltloAylloy
Titanium Alloy
H Hardened steel
(Note 1) VP20RT is the first recommended grade for materials other than hardened steel.
(Note 2) For VP10RT, VP20RT and MY5015, wet cutting is recommended.
info@mitsubishitools.ru www.mitsubishitools.ru