2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN

                                                                         для заказа - info@mitsubishitools.ru

      INTERNAL THREADING

      FTYPE                                                       a	Minimum cutting diameter 10mm.
          BORING BARS                                             a	Screw-on type.
                                                                  a	Applicable to threading, grooving and boring.
                                                                  a	Thread pitch 1.5  3.5mm.

      FSL51                                            Internal threading, Grooving, Boring

                                                                               1 Corner Type   F1
                                                                            (FSL5108R, 5110R)             F1

                                                                                                                                                       D4
                                                                                                          2° 2°
                                                                                                                       L2

                                                                                               10° L1

                                                                           2 Corner Type             2° 2° L2                                                 H1
                                                                  (FSL5112R, 5114R, 5116R)  5° L1                                                             D4

      (Note)	Cutting in the opposite                                                                                                  Right hand tool holder only.
               direction is not possible.
                                                                                                                         *Min.
THREADINGOrder Number                                  Insert Number                        Dimensions (mm)
                                                Stock                                       L1 L2 F1                         Cutting
                                                     R Threading  Grooving  D4                                      H1 Diameter Clamp Screw Wrench
                                                                             8
      FSL5108R                                       a MLT1001L MLG10ooL                    125 30 4.8 7                     10                               TS25  TKY08F
                                                                            10
      5110R                                          a MLT1001L MLG10ooL    12              150 40 5.8 9                     12                               TS25  TKY08F
                                                                            14
      5112R                                          a MLT1401L MLG14ooL    16              180 50 6.8 10.8 14                                                TS32  TKY08F

      5114R                                          a MLT1401L MLG14ooL                    180 60 7.8 12.4 16                                                TS32  TKY08F

      5116R                                          a MLT2001L MLG20ooL                    200 70 9.7 14                    20                               TS43  TKY15F

      * Clamp Torque (N • m) : TS25=1.0, TS32=1.0, TS43=3.5

      FSL52 Carbide shank

                                                                               1 Corner Type   F1
                                                                            (FSL5208R, 5210R)              F1

                                                                                                                                                         D4
                                                                                                          2° 2°
                                                                                                                       L2

                                                                                               10° L1

                                                                           2 Corner Type             2° 2° L2                                                 H1
                                                                  (FSL5212R, 5214R, 5216R)  5° L1                                                             D4

      (Note)	Cutting in the opposite                                                                                                Right hand tool holder only.
               direction is not possible.

      Order Number       Stock                         Insert Number                         Dimensions (mm)                *Min.

                                                     R Threading  Grooving  D4               L1 L2 F1               H1      Cutting                                 Wrench
                                                                             8              125 60 4.8               7     Diameter Clamp Screw
                                                                                            150 70 5.8               9
      FSL5208R                                       a MLT1001L MLG10ooL    10              180 80 6.8                       10                               TS25  TKY08F
                                                                            12              180 85 7.8              11
      5210R                                          a MLT1001L MLG10ooL    14              200 115 9.7             12       12                               TS25  TKY08F
                                                                            16                                      14
      5212R                                          a MLT1401L MLG14ooL                                                     14                               TS32  TKY08F

      5214R                                          a MLT1401L MLG14ooL                                                     16                               TS32  TKY08F

      5216R              s MLT2001L MLG20ooL                                                                                 20                               TS43  TKY15F

      * Clamp Torque (N • m) : TS25=1.0, TS32=1.0, TS43=3.5

      RECOMMENDED CUTTING CONDITIONS

        Work Material     Hardness                     Grade      Cutting Speed (m/min)       Work Material        Hardness          Grade                         Cutting Speed (m/min)
      P                    < 180HB                     UP20M        140 (100 180)          M                       < 200HB          UP20M                            120 (80 150)
                                                       UTi20T       120 (100 150)                                                   UTi20T                           100 (70 130)
             Mild Steel  180  280HB                   UP20M        120 (100 150)             Stainless Steel                       UP20M                             80 (60 100)
                                                       UTi20T        100 (70 120)                                                   UTi20T                            80 (60 100)
          Carbon Steel                                                                      K                      Tensile Strength
            Alloy Steel                                                                            Cast Iron            < 350MPa

G030  a : Inventory maintained. s : Inventory maintained in Japan.                          www.mitsubishitools.ru
                                                             info@mitsubishitools.ru