2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
MSTAR END MILLS
CARBIDE MS2XL6
End mill, Short cut length, 2 flute, 6mm shank
RECOMMENDED CUTTING CONDITIONS
Work material Carbon steel, Cast iron, Alloy steel, Tool steel,
Alloy steel ( 30HRC) Pre-hardened steel
Cf53, GG25 X40CrMoV51
Dia. Neck length Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
(mm) (mm) (min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm)
/ 0.8 40000 500 1000 0.01 30000 300 800 0.01
0.3 1.5 40000 500 1000 0.007 30000 300 800 0.007
40000 500 1000 0.015 30000 300 800 0.015
0.4 1 33000 500 1000 0.01 25000 300 800 0.01
2 29000 500 1000 0.02 22000 300 800 0.02
25000 500 1000 0.013 20000 300 800 0.013
0.5 1.3 22000 500 1000 0.03 18000 300 800 0.03
2.5 20000 500 1000 0.018 16000 300 800 0.018
18000 500 1000 0.04 14000 300 800 0.04
0.6 1.5 16000 500 1000 0.025 13000 300 800 0.025
3 15000 500 1000 0.06 12000 300 800 0.06
14000 500 1000 0.03 11000 300 800 0.03
0.7 1.8 13000 500 1000 0.08 10000 300 800 0.08
3.5 12000 500 1000 0.05 10000 300 800 0.05
12000 500 1000 0.1 300 800 0.1
0.8 2 11000 500 1000 0.07 9500 300 800 0.07
4 10000 500 1000 0.12 9000 300 800 0.12
10000 500 1000 0.08 9000 300 800 0.08
0.9 2.3 500 1000 0.12 9000 300 800 0.12
4.5 9800 500 1000 0.08 9000 300 800 0.08
9600 500 1000 0.12 9000 300 800 0.12
1 2.5 9400 500 1000 0.08 8800 300 800 0.08
5 9200 500 1000 0.12 8700 300 800 0.12
9000 0.08 8500 0.08
SOLID END MILLS 1.1 2.8 0.15 0.15
5.5 0.1 0.1
0.15 0.15
1.2 3 0.1 0.1
6 0.17 0.17
0.12 0.12
1.3 3.3 0.17 0.17
6.5 0.12 0.12
0.17 0.17
1.4 3.5 0.12 0.12
7 0.2 0.2
0.15 0.15
1.5 3.8 0.2 0.2
7.5 0.15 0.15
0.2 0.2
1.6 4 0.15 0.15
8 0.2 0.2
0.15 0.15
1.7 4.3 0.25 0.25
8.5 0.2 0.2
0.25 0.25
1.8 4.5 0.2 0.2
9
1.9 4.8
9.5
2 5
10
2.1 5.3
10.5
2.2 5.5
11
2.3 5.8
11.5
2.4 6
12
2.5 6.3
12.5
ap:Depth of Cut in the Axial Direction
1) If the depth of cut is shallow, the revolution and feed rate can be increased.
2) Cutting conditions may be considerably different due to the overhang (milling depth), depth of cut, and machine tool. Please see the above
table as a standard.
I050 info@mitsubishitools.ru www.mitsubishitools.ru