2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
MSTAR END MILLS
CARBIDE MSMHZD
End mill, Medium cut length, 3 flute
RECOMMENDED CUTTING CONDITIONS y Plunging
y Shoulder milling
Carbon steel, Cast iron, Alloy steel, Tool steel, Austenitic stainless steel, Heat resistant alloys Carbon steel, Cast iron, Alloy steel, Tool steel, Austenitic stainless steel,
Work Alloy steel ( 30HRC) Pre-hardened steel Titanium alloy Work Alloy steel ( 30HRC) Pre-hardened steel Titanium alloy
material Cf53, GG25 X40CrMoV51 X5CrNi1810, Inconel718 material Cf53, GG25 X40CrMoV51 X5CrNi1810,
X5CrNiMo17122, Ti6Al4V X5CrNiMo17122, Ti6Al4V
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate
(mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
1 19000 600 13000 310 10000 200 9500 65 1 13000 80 10000 50 6000 10
1.5 14000 600 9000 310 7500 210 6400 75 1.5 12000 120 8000 80 6000 20
2 11000 600 7200 310 6000 210 4800 75 2 11000 200 7200 140 6000 30
3 8500 770 5300 380 4400 220 3200 100 3 4200 50
4 7200 850 4400 480 3700 250 2400 130 4 8500 250 5300 180 3300 60
6 5300 940 3200 490 2700 270 1600 130 6 7200 300 4400 210 2200 70
8 4000 1010 2400 560 2000 280 1200 120 8 5300 300 3200 210 1600 80
10 3200 1000 1900 480 1600 300 110 10 4000 320 2400 220 1300 70
12 2700 950 1600 440 1300 300 950 90 12 3200 340 1900 240 1100 70
16 2000 720 1200 350 1000 260 800 70 16 2700 320 1600 220 55
20 1600 600 1000 290 800 240 600 60 20 2000 250 1200 180 800 55
480 1600 200 1000 140 640
<0.2D (D>& 3) <0.2D (D> & 3) < 1.5D 0.05D Depth of <1D (D > & 2) <0.5D (D > & 2)
Depth of <0.1D (D< &3) 1.5D cut
<1.5D <0.1D (D< & 3) <0.5D (D<&2) <0.2D (D < & 2)
cut
D:Dia.
SOLID END MILLS D:Dia.
y Slotting
Carbon steel, Cast iron, Alloy steel, Tool steel, Austenitic stainless steel, Heat resistant alloys
Work Alloy steel ( 30HRC) Pre-hardened steel Titanium alloy
material Cf53, GG25 X40CrMoV51 X5CrNi1810, Inconel718
X5CrNiMo17122, Ti6Al4V
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate
(mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
1 13000 130 10000 80 6000 30 5700 25
1.5 12000 250 8000 150 6000 60 3800 30
2 11000 500 7200 260 6000 130 2800 35
3 8500 640 5300 320 4200 130 1900 50
4 7200 650 4400 370 3300 140 1400 70
6 5300 720 3200 380 2200 140 950 70
8 4000 780 2400 430 1600 140 720 60
10 3200 770 1900 370 1300 150 570 50
12 2700 730 1600 340 1100 150 480 40
16 2000 600 1200 290 800 130 360 30
20 1600 500 1000 240 640 120 290 25
D D D 0.2D
Depth of <1D (D > &2) <0.5D (D > &2)
cut
<0.5D (D<&2) <0.2D (D< &2)
D:Dia.
1) When cutting austenitic stainless steels, the use of water-soluble cutting fluid is effective.
2) If the depth of cut is shallow, the revolution and feed rate can be increased.
3) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and
feed rate proportionately.
I058 info@mitsubishitools.ru www.mitsubishitools.ru