2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
TURNING INSERTS
TURNING INSERTS CLASSIFICATION
Application
ToleranceNEGATIVE INSERTS WITH HOLE
Breaker Name Features Cross Section
and Geometry
Picture
LK First recommendation for cast iron turning Cast Iron Flank
15° 0.15
4
Positive land allows sharp cutting edge and low cutting resistance. ap (mm) 3
2
1 6°
0 0.1 0.3 0.5
f (mm/rev)
LS First recommendation for difficult to cut materials Difficult-to-Cut Materials Flank
4
Enhanced chip disposal for depths of cut smaller than the corner R. ap (mm) 3 20° 0.15
2
1
0 0.1 0.3 0.5
f (mm/rev)
SH For light cutting of carbon steel, alloy steel and Carbon Steel • Alloy Steelap (mm)15° Nose
15°
stainless steel 4 Flank
0.2
Double sided chipbreaker. 3
Can be used at low depth of cuts and high feed rates.
The curved edge allows smooth chip discharge. 2
Recommended for workpieces in the 160 250HB range.
1
0 0.1 0.3 0.5
f (mm/rev)
SA Alternative chipbreaker for light cutting of carbon steel Carbon Steel • Alloy Steel Nose
and alloy steel 25° 0.3
M 4ap (mm)
Double sided chipbreaker. 10°
Superior chip control at small depth of cuts. 3
Covers copying and back turning with wavy edge. Flank
2 25° 0.34
Recommended for workpieces in the 200 300HB range. 1 8°
0 0.1 0.3 0.5
f (mm/rev)
Light Cutting SW Wiper insert for light cutting of carbon steel and alloy steel Carbon Steel • Alloy Steel Nose
4 18° 0.15
Double sided chipbreaker.
The wiper allows up to double the feed rate. ap (mm) 3 7°
Wiper design for increased productivity and improved surface finish.
2 Flank
1 18° 0.15
0 0.1 0.3 0.5
7°
f (mm/rev)
SY First recommendation for light cutting of mild steel Mild Steel Nose
10°
4
Double sided chipbreaker. ap (mm) 3
Effectively controls adhesive chips. 2 Flank
Suitable for mild steel light cutting. 1 10° 0.2
0 0.1 0.3 0.5
f (mm/rev)
R/L-1G Alternative chipbreaker for light cutting of carbon steel Carbon Steel • Alloy Steel Flank
and alloy steel 0.2
4ap (mm) 15°
Double sided chipbreaker.
Parallel chipbreaker controls chip flow. 3
Suitable for finish-light cutting.
Precision chipbreaker. 2
1
0 0.1 0.3 0.5
f (mm/rev)
R/L-K Light cutting Carbon Steel • Alloy Steelap (mm)14° Flank
0.25
Double sided chipbreaker. 4
Nose
G Parallel chipbreaker. 3 Flank
Excellent chip control at low to medium feed rates. 2
1
0 0.1 0.3 0.5
f (mm/rev)
MJ First recommendation for light cutting of Difficult-to-Cut Materialsap (mm)13°
M difficult-to-cut materials 9°
4
Double sided chipbreaker.
Ideal for heat-resistant alloy and titanium alloy. 3
The sharp edge produces a good surface finish.
The curved edge allows smooth chip discharge. 2
1
0 0.1 0.3 0.5
f (mm/rev)
A044 info@mitsubishitools.ru www.mitsubishitools.ru