2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
MSTAR END MILLS
CARBIDE MS2XB
Ball nose, 2 flute, Taper neck
RECOMMENDED CUTTING CONDITIONS
Work material Carbon steel, Cast iron, Work material Carbon steel, Cast iron,
Alloy steel, Pre-hardened steel Alloy steel, Pre-hardened steel
Cf53, GG25 Cf53, GG25
R Taper angle Neck length Depth of cut Revolution Feed rate R Taper angle Neck length Depth of cut Revolution Feed rate
(mm) one side (mm) ap (mm) (min-1) (mm/min) (mm) one side (mm) ap (mm) (min-1) (mm/min)
30' 1.5 0.005 30000 300 30' 10 0.05 22000 530
30000
30' 2 0.005 30000 300 30' 20 0.02 22000 600
30000 300 20000 700
1° 1.5 0.005 30000 300 30' 30 0.005 18000
30000 1000
1° 2 0.005 400 1° 10 0.05 16000
14000 1300
R0.1 2° 1.5 0.01 500 R0.5 1° 20 0.02 1100
2° 2 0.01 1° 35 0.005
3° 1.5 0.01 2° 20 0.03
3° 2 0.01 3° 40 0.05
5° 2 0.01 5° 20 0.05
30' 3 0.005 30' 12 0.05
1° 3 0.005 30' 24 0.02
R0.15 2° 3 0.01 R0.6 1° 12 0.05
1° 24 0.02
3° 3 0.01
5° 3 0.01 2° 12 0.06
30' 2 0.02 2° 24 0.03
30' 5 0.01
30' 10 0.1
SOLID END MILLS R0.2 1° 2 0.02 30' 30 0.02
1° 5 0.01
R0.75 1° 10 0.1
2° 2 0.02 1° 30 0.05
2° 5 0.01 2° 30 0.1
30' 3 0.03 30' 20 0.05
30' 5 0.02 30' 30 0.03
R0.25 1° 3 0.03 30' 40 0.02
1° 5 0.02
1° 20 0.05
2° 3 0.03 R1 1° 40 0.03
2° 5 0.02 1° 50 0.02
30' 5 0.03 2° 40 0.1
30' 8 0.02 3° 40 0.1
1° 5 0.03 5° 38.2 0.1
R0.3 1° 10 0.02 30' 30 0.1
1° 15 0.01 30' 50 0.03
2° 6 0.03 R1.5 1° 30 0.1
1° 50 0.03
2° 8 0.02
30' 8 0.05 2° 48.9 0.1
30' 12 0.04 3° 50 0.1
R0.4 1° 8 0.05 R2 30' 60 0.1
1° 12 0.04 1° 60 0.1
2° 8 0.08
3° 12 0.06
< 0.1R (R < 0.5)
< 0.2R (R > 0.5)
Depth of cut
ap R:Radius
1) If the depth of cut is shallow, the revolution and feed rate can be increased.
2) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and
feed rate proportionately.
I086 info@mitsubishitools.ru www.mitsubishitools.ru