2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
CARBIDE
RECOMMENDED CUTTING CONDITIONS
y Shoulder milling
Carbon steel, Cast iron, Alloy steel, Tool steel, Austenitic stainless steel, Hardened steel (45 55HRC) Heat resistant alloys
Work Alloy steel ( 30HRC) Pre-hardened steel Titanium alloy
material Cf53, GG25 X40CrMoV51 X5CrNi1810, X5CrNiMo17122, X40CrMoV51 Inconel718
Ti6Al4V
Revolution
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate (min-1) Feed rate
(mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (mm/min)
4800
2 15000 550 10000 340 10000 320 6400 160 4000 100
3 11000 800 7400 500 7400 480 4800 250 3200 170
4 900 5600 540 5600 520 3600 270 2600 240
5 8000 1000 4500 600 4500 580 2900 300 2100 240
6 6400 1100 3700 640 3700 600 2400 320 1600 230
8 5900 1100 2800 660 2800 600 1800 330 1300 220
10 4400 1000 2300 640 2300 560 1400 320 1100 200
12 3500 1000 1900 640 1900 530 1200 320 170
16 2900 800 1400 500 1400 450 250 800 130
18 2200 800 1250 480 1250 450 900 240 710 110
20 2000 750 1100 460 1100 440 800 230 650 100
1800 720
< 0.2D < 0.1D < 0.05D
Depth of < 1.5D < 1.5D < 1.5D
cut
D:Dia.
y Slotting SOLID END MILLS
Carbon steel, Cast iron, Alloy steel, Tool steel, Austenitic stainless steel, Hardened steel (45 55HRC) Heat resistant alloys
Work Alloy steel ( 30HRC) Pre-hardened steel Titanium alloy
material Cf53, GG25 X40CrMoV51 X5CrNi1810, X5CrNiMo17122, X40CrMoV51 Inconel718
Ti6Al4V
Revolution
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate (min-1) Feed rate
(mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (mm/min)
2300
2 12000 400 7000 200 7000 100 4200 80 1900 40
3 9000 600 5300 300 5300 150 3200 130 1400 70
4 7200 720 4000 360 4000 180 2400 140 1100 95
5 5800 720 3200 360 3200 180 1900 150 95
6 5000 800 2700 400 2700 200 1600 160 950 95
8 3700 800 2000 400 2000 200 1200 170 720 90
10 3000 720 1600 360 1600 180 160 570 80
12 2500 600 1300 290 1300 150 960 140 480 70
16 2000 480 1000 230 1000 120 800 110 360 50
18 1800 460 210 110 600 110 320 45
20 1600 430 900 200 900 100 550 100 290 40
800 800 480
D D < 0.2D
D
Depth of < 1D < 0.5D
cut (MAX. 12mm)
D:Dia.
1) When cutting austenitic stainless steels, the use of water-soluble cutting fluid is effective.
2) If the depth of cut is shallow, the revolution and feed rate can be increased.
3) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and
feed rate proportionately.
info@mitsubishitools.ru www.mitsubishitools.ru I097