2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
CARBIDE
RECOMMENDED CUTTING CONDITIONS
Work material Carbon steel, Cast iron, Alloy steel, Hardened steel (45 55HRC)
Pre-hardened steel X40CrMoV51
Cf53, GG25
Small Mill Dia. Length of cut Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
(min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm)
(mm) (mm)
0.2 2 20000 40000 200 500 0.001 20000 40000 150 300 0.001
0.3 3 20000 40000 200 500 0.002 20000 40000 150 300 0.001
0.4 4 20000 40000 200 500 0.003 20000 36000 150 300 0.002
0.5 4 20000 38000 200 500 0.01 16000 29000 200 400 0.005
6 0.005 13000 24000 200 400 0.003
0.01 0.005
0.6 4 18000 32000 250 600 0.007 0.004
6
0.7 6 16000 27000 250 600 0.015 11000 20000 200 400 0.008
8 0.01 10000 18000 200 400 0.005
0.03 0.015
4 0.02 0.01
0.013 0.007
0.8 8 14000 24000 250 600
12
6 0.03 8000 14000 200 500 0.015
1.0 10 11000 19000 300 800 0.02 0.01
0.015 0.008
16
6 0.04 0.02
0.03 0.015
1.2 10 9200 16000 300 800 0.02 6600 12000 200 500 0.01
16 0.01 0.007
8500 15000 300 800 0.03 6100 11000 200 500 0.015
20 8000 14000 300 800 0.035 5700 10000 200 500 0.018 SOLID END MILLS
0.06 0.03
1.3 12 7500 13000 300 800 0.04 5300 9500 200 500 0.02
0.03 0.015
1.4 12 0.015 0.008
0.06 0.03
6 0.045 0.025
0.035 0.02
1.5 10 0.025 0.015
16 0.08 0.04
0.05 0.03
25 0.03 0.015
8
1.6 12 7000 12000 300 800 5000 9000 200 500
16
20
8
1.8 16 6200 11000 300 800 4400 8000 200 500
24
8 0.1 0.05
0.07 0.04
2.0 12 5500 9500 300 800 0.04 4000 7200 200 500 0.02
20 0.02 0.01
30
10 4400 7600 300 800 0.1 3200 5700 200 500 0.05
2.5 20 0.06 0.03
0.03 0.015
30
3.0 25 3700 6400 300 800 0.08 2700 4800 200 500 0.04
40 0.04 0.02
ap:Depth of Cut in the Axial Direction
1) If the depth of cut is shallow, the revolution and feed rate can be increased.
2) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and
feed rate proportionately.
info@mitsubishitools.ru www.mitsubishitools.ru I109