2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
CARBIDE
Unit : mm
Order Number R B7 ap D2 L1 D4 Flutes Stock Type
MS2MTBR0125T0400 1.25 4° 10 3.73 50 6 2s1 SQUARE
R0125T0500 1.25 5° 10 4.04 50 6 2s1
R0125T0700 1.25 7° 14.5 5.77 60 6 2s2
R0150T0700 1.5 7° 12.5 5.72 60 6 2s2
BALL
RECOMMENDED CUTTING CONDITIONS Hardened steel (45 55HRC) RADIUS
X40CrMoV51
Carbon steel, Cast iron, Alloy steel,
Work Pre-hardened steel
material Cf53, GG25
R %< 15° %>15° Depth of cut %< 15° %>15° Depth of cut TAPER
(mm)
Revolution Feed rate Revolution Feed rate (mm) Revolution Feed rate Revolution Feed rate (mm)
R 0.1 (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
R 0.15 0.003 0.003
R 0.2 40000 300 40000 250 0.007 40000 300 40000 250 0.007 SOLID END MILLS
R 0.25 40000 500 40000 350 0.02 40000 500 40000 350 0.015
R 0.3 40000 1600 40000 1200 0.025 40000 1300 40000 950 0.020
R 0.4 40000 2400 0.03 40000 1900 0.025
R 0.5 40000 3200 40000 1400 0.05 40000 2500 40000 1100 0.04
R 0.75 40000 4800 0.06 40000 4000 0.05
R1 40000 5600 40000 1600 0.09 40000 5600 40000 1300 0.08
R 1.25 40000 6500 40000 2400 0.11 40000 6500 40000 1900 0.11
R 1.5 40000 6500 40000 3200 0.12 40000 6500 40000 3000 0.12
R2 40000 7000 0.13 36000 6500 0.13
R 2.5 40000 7500 40000 4000 0.15 32000 6000 32000 3200 0.15
R3 32000 7500 0.20 25000 6000 0.20
R4 25000 6000 39000 4700 0.25 20000 5400 31000 3500 0.25
R5 21000 5800 33000 4500 0.30 17000 4700 26000 3500 0.30
R6 16000 4500 27000 4300 0.50 13000 3600 22000 3400 0.50
13000 3600 0.50 10000 2900 0.50
2500 20000 3600 2000 16000 2700
9000 7200
16000 2900 13000 2300
13000 2600 10000 2000
10000 2000 1500
8000
8000 1700 6400 1200
6000 1300 4800 1000
Depth of < 0.2R
cut
< Please refer to the list above for depth of cut.
R:Radius
1) % is the inclination angle of the machined surface.
2) If the depth of cut is shallow, the revolution and feed rate can be increased.
3) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and
feed rate proportionately.
End mill ap
R
%
pf
info@mitsubishitools.ru www.mitsubishitools.ru I115