2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
VF2XLBS VF2XLB CARBIDE
Ball nose, Medium cut length, 2 flute, Short shank Ball nose, Long cut length, 2 flute, For hardened materials
RECOMMENDED CUTTING CONDITIONS
Hardened steel (45 55HRC) Hardened steel (55 62HRC) Hardened steel (45 55HRC) Hardened steel (55 62HRC)
Work X40CrMoV51 X210Cr12 Work X40CrMoV51 X210Cr12
material material
R Neck Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut R Neck Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
(mm) length (min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm) (mm) length (min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm)
(mm) (mm)
0.5 40000 300 0.003 40000 300 0.002 R 0.75 18 13000 1100 0.02 10000 800 0.02
20 12000 900 0.02 9000 700 0.01
1 40000 300 0.002 40000 300 0.002
R 0.1 1.5 40000 300 0.001 40000 200 0.001 8 40000 5000 0.08 26000 3200 0.07
2 40000 200 0.001 40000 100 0.001 R 0.8 12 35000 3800 0.05 20000 2100 0.03
16 13000 1200 0.04 12000 1100 0.02
2.5 40000 100 0.001 40000 60 0.001
1 40000 500 0.007 40000 500 0.005 20 10000 750 0.02 8000 600 0.01
1.5 40000 500 0.005 40000 500 0.003 8 40000 5000 0.09 25000 3100 0.08
R 0.15 2 40000 500 0.003 40000 500 0.002 R 0.9 12 36000 3800 0.06 18000 1900 0.04
2.5 40000 400 0.003 40000 400 0.002 16 25000 2500 0.04 14000 1300 0.025
3 40000 300 0.002 40000 300 0.001 20 10000 1000 0.03 8000 800 0.02
4 30000 200 0.002 30000 200 0.001 6 40000 6000 0.1 24000 3400 0.1
1 40000 1400 0.015 40000 1400 0.01 8 40000 5000 0.1 24000 3000 0.1
1.5 40000 1000 0.01 40000 1000 0.006 10 40000 5000 0.08 24000 3000 0.07
2 40000 1000 0.01 40000 1000 0.006 12 40000 5000 0.08 24000 2600 0.05
R 0.2 2.5 40000 700 0.005 40000 700 0.003 14 40000 5000 0.06 21000 2300 0.05
3 40000 700 0.005 40000 700 0.003 R1 16 32000 3500 0.05 16000 1700 0.03
18 24000 2400 0.04 13000 1300 0.03
4 40000 600 0.004 40000 500 0.003
5 40000 400 0.003 40000 300 0.002 20 10000 1000 0.04 10000 1000 0.03
1.5 40000 2000 0.02 40000 2000 0.015 22 10000 1000 0.04 10000 1000 0.02
2 40000 2000 0.02 40000 2000 0.015 25 10000 1000 0.04 8000 800 0.02
R 0.25 3 40000 1200 0.015 40000 1200 0.01 30 10000 800 0.02 8000 800 0.015
4 36000 900 0.01 36000 900 0.007
35 10000 500 0.02 8000 400 0.01
5 36000 700 0.007 36000 600 0.005 10 36000 5000 0.12 20000 2600 0.11
6 36000 600 0.006 36000 500 0.004 15 36000 4600 0.08 18000 2000 0.075 SOLID END MILLS
2 40000 2800 0.03 40000 2800 0.02 R 1.25 20 26000 3000 0.07 13000 1400 0.05
25 10000 1100 0.06 8000 800 0.04
3 40000 2800 0.03 40000 2800 0.02
4 35000 2000 0.02 35000 2000 0.015 30 8000 800 0.05 7000 700 0.03
R 0.3 5 30000 1000 0.01 30000 1000 0.007 35 8000 500 0.03 5000 400 0.03
6 30000 800 0.008 30000 800 0.005 8 32000 6400 0.15 16000 3000 0.15
7 30000 600 0.008 30000 600 0.005 10 32000 5100 0.15 16000 2200 0.15
8 25000 400 0.006 25000 400 0.004 12 32000 5100 0.13 16000 2200 0.13
2 40000 3500 0.04 40000 3500 0.03 14 32000 4500 0.13 16000 2200 0.1
3 40000 3000 0.04 40000 3000 0.03 R 1.5 16 32000 4500 0.1 16000 1800 0.1
20 27000 3800 0.1 14000 1600 0.06
R 0.4 4 40000 3000 0.02 40000 3000 0.015
6 30000 1600 0.02 30000 1600 0.01 25 21000 2700 0.08 11000 1200 0.06
8 25000 1000 0.01 25000 1000 0.007 30 9000 1000 0.08 7000 700 0.05
10 25000 600 0.008 25000 600 0.005 35 6000 700 0.06 6000 600 0.04
3 40000 4000 0.05 40000 4000 0.04 40 6000 600 0.04 5000 400 0.03
4 40000 4000 0.05 40000 4000 0.04 16 28000 4200 0.13 14000 1600 0.13
5 40000 3000 0.03 40000 3000 0.02 20 26000 3800 0.13 13000 1600 0.11
6 35000 2000 0.03 35000 2000 0.02 R 1.75 25 23000 3300 0.12 11000 1200 0.08
30 13000 1900 0.09 9000 1000 0.07
8 30000 1600 0.02 30000 100 0.01
R 0.5 10 20000 1000 0.01 20000 1000 0.01 35 9000 1200 0.08 6000 600 0.06
12 20000 1000 0.01 18000 800 0.008 40 8500 1100 0.07 5500 500 0.04
14 18000 600 0.008 18000 480 0.008 10 24000 4800 0.2 12000 2200 0.2
16 18000 500 0.008 18000 400 0.006 12 24000 4800 0.2 12000 2200 0.2
18 13000 300 0.005 13000 240 0.004 14 24000 3800 0.15 12000 1500 0.15
20 13000 250 0.005 13000 200 0.004 16 24000 3800 0.15 12000 1500 0.15
6 40000 4000 0.05 35000 3500 0.04 20 24000 3800 0.15 12000 1500 0.15
R 2 25 24000 3800 0.15 10000 1100 0.1
8 40000 3000 0.05 27000 2000 0.04
R 0.6 10 27000 1900 0.03 24000 1700 0.02 30 20000 3000 0.1 10000 1100 0.08
12 16000 1100 0.02 16000 1000 0.01
35 12000 1700 0.1 8000 900 0.08
14 16000 850 0.01 16000 780 0.01 40 11000 1500 0.1 5000 500 0.06
16 15000 500 0.01 14000 400 0.006 45 10000 1300 0.08 5000 500 0.05
8 40000 4500 0.06 28000 3200 0.05 50 8000 1000 0.05 4000 400 0.04
R 0.7 12 32000 3000 0.03 19000 1800 0.02
15000 1000 0.02 14000 0.01 20 19000 3400 0.2 10000 1400 0.2
16 800
R 2.5 25 19000 3400 0.2 10000 1400 0.2
6 40000 5000 0.07 32000 4000 0.06 30 19000 3200 0.15 8000 1000 0.15
8 40000 5000 0.07 28000 3500 0.06 35 16000 2700 0.1 8000 900 0.1
R 0.75 10 40000 4500 0.06 21000 2400 0.04 30 16000 3500 0.2 8000 1000 0.2
12 32000 3400 0.04 19000 2000 0.03 R 3 40 16000 3000 0.15 8000 800 0.15
14 16000 1500 0.04 13000 1200 0.03 50 16000 2700 0.15 6000 500 0.15
16 13000 1200 0.03 13000 1200 0.02
< 0.1R (R< 1)
< 0.2R (R >1)
Depth of cut
ap
R:Radius
1) If the depth of cut is shallow, the revolution and feed rate can be increased. I181
2) Cutting condition may be considerably different due to the overhang (milling depth), depth of cut, and machine tools.
Please see the above table as a standard.
info@mitsubishitools.ru www.mitsubishitools.ru