2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
CARBIDE
RECOMMENDED CUTTING CONDITIONS
Carbon steel, Cast iron, Alloy steel, Tool steel, Hardened steel (45 55HRC) Hardened steel (55 62HRC)
Alloy steel ( 30HRC) Pre-hardened steel
Work material
Cf53, GG25 X40CrMoV51
X40CrMoV51 X210Cr12
R Taper angle Neck length Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
(mm) (min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm)
one side (mm)
R0.4
0.4° 6 34000 2700 0.03 31000 2200 0.025 24000 1700 0.02 19000 1400 0.015
R0.5 8 31000 2100 0.02 29000 1700 0.02 22000 1300 0.015 18000 1000 0.01
12 28000 2000 0.015 26000 1600 0.01 20000 1200 0.01 16000 960 0.007
R0.75
0.9° 8 31000 2200 0.02 29000 1800 0.02 22000 1400 0.015 18000 1100 0.01
12 28000 2100 0.015 26000 1700 0.01 20000 1300 0.01 16000 1000 0.007
16 25000 1100 0.01 23000 910 0.01 18000 700 0.008 14000 560 0.006
8 27000 2700 0.04 25000 2200 0.04 19000 1700 0.03 15000 1400 0.02
10 24000 2200 0.03 22000 1800 0.025 17000 1400 0.02 14000 1100 0.015
0.4° 12 24000 2200 0.03 22000 1800 0.025 17000 1400 0.02 14000 1100 0.015
16 22000 2100 0.03 21000 1700 0.025 16000 1300 0.02 13000 1000 0.015
20 20000 1400 0.015 18000 1200 0.01 14000 900 0.01 11000 720 0.007
25 18000 1300 0.015 17000 1000 0.01 13000 800 0.009 10000 640 0.006
30 15000 960 0.01 14000 780 0.01 11000 600 0.008 8800 480 0.006
35 14000 800 0.008 13000 650 0.007 10000 500 0.006 8000 400 0.004
8 27000 2900 0.04 25000 2300 0.04 19000 1800 0.03 15000 1400 0.02
12 24000 2400 0.03 22000 2000 0.025 17000 1500 0.02 14000 1200 0.015
16 22000 2200 0.03 21000 1800 0.025 16000 1400 0.02 13000 1100 0.015 SOLID END MILLS
20 20000 1600 0.015 18000 1300 0.01 14000 1000 0.01 11000 800 0.007
25 18000 1400 0.015 17000 1200 0.01 13000 900 0.009 10000 720 0.006
0.9° 30 15000 1100 0.01 14000 910 0.009 11000 700 0.008 8800 560 0.006
35 14000 960 0.008 13000 780 0.007 10000 600 0.006 8000 480 0.004
40 11000 800 0.007 11000 650 0.006 8000 500 0.005 6400 400 0.003
50 8400 610 0.006 7800 490 0.005 6000 380 0.004 4800 300 0.003
60 7000 510 0.004 6500 400 0.004 5000 320 0.003 4000 260 0.002
70 7000 480 0.003 6500 390 0.002 5000 300 0.002 4000 240 0.001
12 24000 2600 0.03 22000 2100 0.025 17000 1600 0.02 14000 1300 0.015
16 22000 2400 0.03 21000 2000 0.025 16000 1500 0.02 13000 1200 0.015
1.5° 20 20000 1800 0.015 18000 1400 0.01 14000 1100 0.01 11000 880 0.007
25 18000 1600 0.015 17000 1300 0.01 13000 1000 0.009 11000 800 0.006
30 15000 1300 0.01 14000 1000 0.01 11000 800 0.008 8800 640 0.006
35 14000 1100 0.008 13000 910 0.007 10000 700 0.006 8000 560 0.004
0.4° 10 18000 2700 0.06 17000 2200 0.05 13000 1700 0.04 10000 1400 0.03
15 17000 2200 0.04 16000 1800 0.04 12000 1400 0.03 9600 1100 0.02
20 17000 2100 0.03 16000 1700 0.025 12000 1300 0.02 9600 1000 0.015
30 14000 1600 0.015 13000 1300 0.01 10000 1000 0.01 8000 800 0.007
15 17000 2400 0.04 16000 2000 0.04 12000 1500 0.03 9600 1200 0.02
0.9° 20 17000 2200 0.03 16000 1800 0.025 12000 1400 0.02 9600 1100 0.015
30 14000 1800 0.015 13000 1400 0.01 10000 1100 0.01 8000 880 0.007
40 13000 1300 0.01 12000 1000 0.01 9000 800 0.008 7200 640 0.006
1.5° 15 17000 2600 0.04 16000 2100 0.04 12000 1600 0.03 9600 1300 0.02
20 17000 2400 0.03 16000 2000 0.025 12000 1500 0.02 9600 1200 0.015
30 14000 2000 0.015 13000 1600 0.01 10000 1200 0.01 8000 960 0.007
Depth of cut < 0.1R (R< 1)
< 0.2R (R >1)
ap
R:Radius
1) If the depth of cut is shallow, the revolution and feed rate can be increased.
2) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and
feed rate proportionately.
info@mitsubishitools.ru www.mitsubishitools.ru I185
