2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN

                                                                                                       для заказа - info@mitsubishitools.ru

                         TURNING INSERTS

TURNING INSERTS          CLASSIFICATION
           Application
                Tolerance7° POSITIVE INSERTS WITH HOLE

                                         Breaker Name                                                  Features                                                 Cross Section
                                                and                                                                                                               Geometry

                                              Picture

                         For Cast Iron         Flat Top Heavy cutting of cast iron                                              Cast Ironap (mm)                0°
                                                                                                                                                                0°
                                                                         Flat top.                                                  3ap (mm)

                                         M Most effective for unstable machining due to its high edge strength.                     2

                                               Flat Top For cast iron                                                               1

                                                                         Flat top.                                                  0 0.1 0.2 0.3 0.4

                                         G Most effective for unstable machining due to its high edge strength.                           f (mm/rev)

                                                                         Can be used on workpieces requiring close tolerances   Cast Iron
                                                                         due to G class insert tolerance.
                                                                                                                                    3

                                                                                                                                    2

                                                                                                                                    1

                                                                                                                                    0 0.1 0.2 0.3 0.4

                                                                                                                                          f (mm/rev)

                         11° POSITIVE INSERTS WITH HOLE

                         Application     Breaker Name                                                  Features                                                 Cross Section
                              Tolerance         and                                                                                                               Geometry

                                              Picture

                                         FV            First recommendation for finishing carbon steel,                         Carbon Steel • Alloy Steel           Nose
                                                       alloy steel, mild steel and stainless steel                                  3 18°                            Flank
                                                                                                                                ap (mm)                              Flank
                                         M Suitable for low depths of cut and low feed rates.                                                2                       Flank
                                                                                                                                                                     Flank
                                                       Sharp cutting edge and low resistance design achieves excellent cutting               1                       Flank
                                                                                                                                                                     Flank
                                                       performance.                                                                          0 0.1 0.2 0.3 0.4  8°

                                                                                                                                                   f (mm/rev)

                                         R/L-FS        First recommendation for finishing carbon steel,                         Carbon Steel • Alloy Steel
                                                       alloy steel, stainless steel, cast iron and
                                         G aluminium alloy                                                                          3ap (mm)

                                                                         Small wide lead chipbreaker.                               2 15°
                                                                                                                                    1
                                                       Sharp cutting edge gives a good surface finish.
                                                                                                                                    0 0.1 0.2 0.3 0.4

                                                                                                                                          f (mm/rev)

                                                 R/L-F Finishing                                                                Carbon Steel • Alloy Steelap (mm)

                                                                         Lead chipbreaker controls chip flow.                       3

                                         M Sharp cutting edge gives a good surface finish.                                          2 15°
                                                                                                                                    1
                         Finish Cutting
                                                                                                                                    0 0.1 0.2 0.3 0.4

                                                                                                                                          f (mm/rev)

                                         R/L-F         Finishing                                                                Carbon Steel • Alloy Steel

                                                       Lead chipbreaker controls chip flow.                                         3ap (mm)
                                                       Sharp cutting edge gives a good surface finish.
                                                                                                                                    2 15°
                                                                                                                                    1

                                                                                                                                    0 0.1 0.2 0.3 0.4

                                                                                                                                          f (mm/rev)

                                                  R/L Finishing                                                                 Carbon Steel • Alloy Steelap (mm)

                                                                         Lead chipbreaker controls chip flow.                       3

                                         G Good chip control for low to medium feed rates.                                          2 10°
                                                                                                                                    1

                                                                                                                                    0 0.1 0.2 0.3 0.4

                                                                                                                                          f (mm/rev)

                                         Standard      Finishing                                                                Aluminium Alloy

                                                       Lead chipbreaker controls chip flow.                                         3ap (mm)                    25°
                                                       Good chip control for low to medium feed rates.                              2
                                                                                                                                    1
                                                                                                                                    0 0.1 0.2 0.3 0.4

                                                                                                                                          f (mm/rev)

A062                                                                 info@mitsubishitools.ru                     www.mitsubishitools.ru