2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
Order Number D1 R ap L3 D5 B2 L1 CARBIDEFlutes
Stock
0.5 3 Unit : mmType
0.2 4
CRN2XLRBD0300R050N20 3 0.3 4 20 2.9 3.4° 65 Effective length SQUARE
D0400R020N20 4 0.5 4 D4 for inclined angle
D0400R030N20 4 0.2 5 20 3.9 2.5° 65
D0400R050N20 4 0.3 5 30' 1° 2° 3°
D0500R020N25 5 0.5 5 20 3.9 2.5° 65 6 2 a 1 20.8 21.5 23.1 24.9
D0500R030N25 5 0.2 6
D0500R050N25 5 0.3 6 20 3.9 2.5° 65 *6 2 a 1 20.8 21.5 23.2
D0600R020N30 6 0.5 6 *6 2 a 1 20.8 21.5 23.1
D0600R030N30 6 16 25 4.9 1.1° 65 *6 2 a 1 20.8 21.5 23.1
D0600R050N30 6 * *6 2 a 1 26 26.9
D0600R100N30 6 25 4.9 1.1° 65 * *6 2 a 1 26 26.9 BALL
* *6 2 a 1 26 26.9
25 4.9 1.1° 65 6 *2 a 2 * * *
6 *2 a 2 * * *
30 5.85 70 6 *2 a 2 * * *
6 *2 a 2 * * *
30 5.85 70
* No interference
30 5.85 70
30 5.85 70 RADIUS
RECOMMENDED CUTTING CONDITIONS y Contour Cutting TAPER
y Slotting
Work material Copper, Copper alloys Copper, Copper alloys
Dia. Corner radius Neck length Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut SOLID END MILLS
(mm) (min-1) (mm/min) ap (mm) (min-1) (mm/min)
(mm) (mm) ap ae
40000 800 0.005 40000 1500 (mm) (mm)
40000 700 0.003 40000 1000
0.5 R0.05, R0.1 4 40000 1200 0.02 40000 2500 0.01 0.1
0.8 R0.05, R0.1 6 40000 1200 0.015 40000 1600 0.005 0.1
6 40000 2000 0.03 40000 3000 0.02 0.15
1 R0.1, R0.3 8 35000 1600 0.025 35000 2000 0.01 0.15
8 30000 1200 0.02 30000 1800 0.03 0.2
1.5 R0.1, R0.2, R0.3 10 30000 1500 0.05 40000 4500 0.025 0.2
12 20000 1000 0.02 20000 2000 0.02 0.2
2 R0.1, R0.2 12 30000 1500 0.1 40000 4500 0.04 0.3
R0.3, R0.5 20 30000 1000 0.06 30000 3000 0.02 0.3
12 20000 600 0.04 20000 2000 0.08 0.4
3 R0.2, R0.3 16 20000 2000 0.12 35000 6000 0.05 0.4
R0.5 20 20000 2200 0.12 35000 8000 0.04 0.4
20 15000 2000 0.25 32000 5000 0.1 0.6
4 R0.2, R0.3 20 15000 2200 0.25 32000 7000 0.1 0.6
R0.5 20 12000 1500 0.3 22000 5000 0.15 0.8
20 12000 1700 0.3 22000 7000 0.15 0.8
5 R0.2, R0.3 25 10000 1200 0.4 20000 5000 0.2 1.0
R0.5 25 10000 1500 0.4 20000 7000 0.2 1.0
30
6 R0.2, R0.3, R0.5 30 D < ae 0.25 1.2
R1 < ap 0.25 1.2
Depth of cut < ap
D:Dia.
1) If the depth of cut is shallow, the revolution and feed rate can be increased.
2) Water-soluble cutting fluid is recommended.
3) Cutting conditions may be considerably different due to the overhang (milling depth), depth of cut, and machine tool. Please see the above
table as a standard.
info@mitsubishitools.ru www.mitsubishitools.ru I267