2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
CARBIDE
Unit : mm
Order Number D1 R ap L3 D5 L1 D4 Flutes Stock Type
AM3SSRBD2000A100R400 20 4 20 40 18.0 100 20 3 a 1 SQUARE
D2000A125R100 20 1 20 60 18.0 125 20 3 a 1
D2000A125R160 20 1.6 20 60 18.0 125 20 3a1
D2000A125R250 20 2.5 20 60 18.0 125 20 3a1
D2000A125R320 20 3.2 20 60 18.0 125 20 3a1
D2000A125R400 20 4 20 60 18.0 125 20 3 a 1 BALL
D2000A150R100 20 1 20 85 18.0 150 20 3 a 1
D2000A150R160 20 1.6 20 85 18.0 150 20 3a1
D2000A150R250 20 2.5 20 85 18.0 150 20 3a1
D2000A150R320 20 3.2 20 85 18.0 150 20 3a1
D2000A150R400 20 4 20 85 18.0 150 20 3 a 1 RADIUS
D2500A100R160 25 1.6 20 50 23.0 100 25 3a1
D2500A100R250 25 2.5 20 50 23.0 100 25 3a1
D2500A100R320 25 3.2 20 50 23.0 100 25 3a1
D2500A100R400 25 4 20 50 23.0 100 25 3 a 1
D2500A100R500 25 5 20 50 23.0 100 25 3 a 1
D2500A125R160 25 1.6 20 65 23.0 125 25 3a1 TAPER
D2500A125R250 25 2.5 20 65 23.0 125 25 3a1
D2500A125R320 25 3.2 20 65 23.0 125 25 3a1
D2500A125R400 25 4 20 65 23.0 125 25 3 a 1
D2500A125R500 25 5 20 65 23.0 125 25 3 a 1
D2500A150R160 25 1.6 20 90 23.0 150 25 3a1 SOLID END MILLS
D2500A150R250 25 2.5 20 90 23.0 150 25 3a1
D2500A150R320 25 3.2 20 90 23.0 150 25 3a1
D2500A150R400 25 4 20 90 23.0 150 25 3 a 1
D2500A150R500 25 5 20 90 23.0 150 25 3 a 1
RECOMMENDED CUTTING CONDITIONS
Work Aluminium alloy
material
Dia. Revolution Feed rate Slotting
(mm) (min-1) (mm/min)
3200
12 13000 Side milling 3200
16 10000 3000
20 5400 2800
25 8000 5400
6000 5000
Depth of 4500
cut < 0.3D
D
0.8D < 0.5D
D:Dia.
1) This table shows the cutting condition with less than 4D overhang length. If more than 4D, spindle speed, feed rate and depth of cut should
be reduced.
2) If the rigidity of the machine or the workpiece installation is very low, or chattering and noise are generated, please reduce the revolution
and the feed rate proportionately.
3) Water-soluble cutting fluid is recommended.
4) Climb cutting is recommended for side milling.
5) Vertical feed is not recommended. To enter the work ramping should be used.
info@mitsubishitools.ru www.mitsubishitools.ru I299