2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
VIOLET END MILLS
HSS VA2SS VA2MS
End mill, Short cut length, 2 flute
End mill, Medium cut length, 2 flute
RECOMMENDED CUTTING CONDITIONS
y Shoulder milling
Work Structural steel, Cast iron, Carbon steel, Alloy steel Alloy steel, Tool steel, Austenitic stainless steel,
material Carbon steel (20 30HRC) Pre-hardened steel (30 35HRC)
Alloy steel, Tool steel
Ck45, GG25, Cf53 Ck55 X40CrMoV51, X210Cr12 (35 40HRC)
X5CrNi1810, X5CrNiMo17-12-2
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate
(mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
3 5400 170 4000 125 2700 85 2200 65
4 4300 200 3200 150 2100 100 1800 75
5 3600 210 2700 160 1800 105 1500 80
6 3200 220 2400 165 1600 110 1300 85
8 2400 240 1800 180 1200 120 1000 90
10 1900 260 1400 190 130 100
12 1600 240 1200 180 950 120 800 90
16 1200 210 160 800 105 660 80
20 180 900 135 600 500 70
25 950 150 720 115 480 90 400 60
30 760 130 570 100 380 75 320 50
40 640 100 480 320 65 270 40
470 350 75 240 50 200
D:Dia.
Depth of < 0.2D
cut
< 1.5D
SOLID END MILLS y Slotting
Work Structural steel, Cast iron, Carbon steel, Alloy steel Alloy steel, Tool steel, Austenitic stainless steel,
material Carbon steel (20 30HRC) Pre-hardened steel (30 35HRC)
Alloy steel, Tool steel
Ck45, GG25, Cf53 Ck55 X40CrMoV51, X210Cr12 (35 40HRC)
X5CrNi1810, X5CrNiMo17-12-2
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate
(mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
3 3700 110 3000 95 2100 65 1600 50
4 3200 140 2800 130 1800 75 1400 60
5 2900 160 2400 145 1500 80 1200 60
6 2600 170 2100 150 1300 85 1000 70
8 2000 190 1600 160 1000 90 70
10 1600 210 1300 180 100 800 80
12 1300 190 1100 165 800 90 640 70
16 1000 170 140 660 80 530 65
20 130 800 120 500 70 400 55
25 720 110 640 400 60 320 40
30 570 450 90 320 50 230 35
40 480 90 370 75 270 40 190 25
360 70 280 60 200 140
D:Dia.
D
Depth of < 0.5D (MAX. 10mm)
cut
1) Supply cutting fluid sufficiently during slotting. When dry cut, slotting decrease the revolution and feed rate by 20 30% proportionately.
2) When drilling, please set the feed rate at 1/3 or below the values above.
3) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and
feed rate proportionately.
I308 info@mitsubishitools.ru www.mitsubishitools.ru