2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
VIOLET END MILLS
HSS VASFPR
Roughing type, Short cut length, 4 6 flute, Fine pitch form
RECOMMENDED CUTTING CONDITIONS
y Shoulder milling
Work Structural steel, Cast iron, Carbon steel, Alloy steel Alloy steel, Tool steel, Austenitic stainless steel,
material Carbon steel (20 30HRC) Pre-hardened steel (30 35HRC)
Alloy steel, Tool steel
Ck45, GG25, Cf53 Ck55 X40CrMoV51, X210Cr12 (35 40HRC)
X5CrNi1810, X5CrNiMo17-12-2
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate
(mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
5 2800 140 2200 120 1500 80 1300 70
6 2600 180 2000 140 1400 90 1200 80
8 2200 230 1700 180 1200 130 100
10 1750 330 1350 250 160 990 130
12 1450 330 1100 260 950 180 800 140
16 1100 330 260 800 180 660 140
20 340 850 260 600 180 500 140
25 880 330 680 250 480 170 400 140
30 700 300 540 230 380 170 320 140
40 580 210 450 170 320 120 270 100
50 350 170 270 130 190 90 160 75
250 190 130 110
D:Dia.
Depth of < 0.5D
cut
< 1.5D
SOLID END MILLS y Slotting
Work Structural steel, Cast iron, Carbon steel, Alloy steel Alloy steel, Tool steel, Austenitic stainless steel,
material Carbon steel (20 30HRC) Pre-hardened steel (30 35HRC)
Alloy steel, Tool steel
Ck45, GG25, Cf53 Ck55 X40CrMoV51, X210Cr12 (35 40HRC)
X5CrNi1810, X5CrNiMo17-12-2
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate
(mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
5 2100 100 1650 80 1150 50 960 35
6 2000 130 1550 100 1050 60 900 45
8 1600 160 1300 90 760 60
10 1300 220 1000 130 920 110 610 80
12 1050 230 175 730 130 500 85
16 230 850 190 610 130 380 85
20 800 230 640 130 300 85
25 640 200 510 190 460 110 240 80
30 510 190 410 90 180 75
40 420 140 320 180 370 70 120 60
50 280 110 210 160 290 55 45
190 150 140 210 85
D:Dia.
110 140
90 95
D
Depth of < 1D (MAX. 30mm)
cut
1) Supply cutting fluid sufficiently during cutting. For dry-cutting, decrease the revolution and feed rate proportionately by 20 50%.
2) For smaller depths and widths of cut, the revolution may be increased by 10 20% and the feed rate by 10 40%.
3) When drilling, please set the feed rate at 1/3 or below the values above.
4) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and
feed rate proportionately.
I312 info@mitsubishitools.ru www.mitsubishitools.ru