2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
iMX-S3HV
Square head, 3 flute, Illegular helix
RECOMMENDED CUTTING CONDITIONS SQUARE
y Side milling
Carbon steel, Alloy steel, Mild Steel, Copper, Pre-hardened steel, Carbon steel, Alloy steel, Austenitic stainless steel,
Work Copper alloys Alloy tool steel Ferritic, Precipitation hardening stainless steel,
material Titanium alloy
Dia. Cutting speed Revolution Feed Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed Feed rate Depth of cut Depth of cut BALL
(mm) (m/min) (min-1) (mm/tooth) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/tooth) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/tooth) (mm/min) ap (mm) ae (mm)
10 150 4800 0.09 1300 8 2 120 3800 0.06 680 8 2 100 3200 0.075 720 8 2 RADIUS
12 150 4000 0.09 1100 9.6 2.4 120 3200 0.065 620 9.6 2.4 100 2700 0.08 650 9.6 2.4
16 150 3000 0.1 900 12.8 3.2 120 2400 0.075 540 12.8 3.2 100 2000 0.09 540 12.8 3.2
20 150 2400 0.1 720 16 4 120 1900 0.075 430 16 4 100 1600 0.09 430 16 4
25 150 1900 0.12 680 20 5 120 1500 0.075 340 20 5 100 1300 0.09 350 20 5
Depth of ae
cut ap
Precipitation hardening stainless steel, Heat resistant alloys
Work Cobalt chromium alloy Inconel718
material
Dia. Cutting speed Revolution Feed Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed Feed rate Depth of cut Depth of cut INDEXABLE HEAD END MILLS
(mm) (m/min) (min-1) (mm/tooth) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/tooth) (mm/min) ap (mm) ae (mm)
10 75 2400 0.06 430 8 2 40 1300 0.04 160 8 1
12 75 2000 0.065 390 9.6 2.4 40 1100 0.045 150 9.6 1.2
16 75 1500 0.075 340 12.8 3.2 40 800 0.05 120 12.8 1.6
20 75 1200 0.075 270 16 4 40 640 0.05 96 16 2
25 75 950 0.075 210 20 5 40 510 0.05 77 20 2.5
Depth of ae
cut ap
1) For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective.
2) If the depth of cut is shallow, the revolution and feed rate can be increased.
3) The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills.
However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur.
In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut.
info@mitsubishitools.ru www.mitsubishitools.ru I339
