2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN

                                                                   для заказа - info@mitsubishitools.ru

iMX-S4HV/iMX-S4HV-S/iMX-C4HV/iMX-C4HV-S

Square/Corner radius, 4 flute, Irregular helix (With/Without coolant hole)

  RECOMMENDED CUTTING CONDITIONS                                                                                                                                          SQUARE

y Slotting

             Carbon steel, Alloy steel, Mild Steel, Copper,  Pre-hardened steel, Carbon steel, Alloy steel,          Austenitic stainless steel,
 Work Copper alloys                                          Alloy tool steel                                        Ferritic, Precipitation hardening stainless steel,
material                                                                                                             Titanium alloy

Dia.      Cutting speed Revolution Feed Feed rate Depth of cut Cutting speed Revolution Feed Feed rate Depth of cut Cutting speed Revolution Feed Feed rate Depth of cut  BALL
(mm)       (m/min) (min-1) (mm/tooth) (mm/min) ap (mm) (m/min) (min-1) (mm/tooth) (mm/min) ap (mm) (m/min) (min-1) (mm/tooth) (mm/min) ap (mm)

10        150 4800 0.06 1200                                 5 120 3800 0.04 610          5 100 3200 0.05 640             5
12
16        150 4000 0.06 960                                  6 120 3200 0.045 580         6 100 2700 0.055 590            6
20
25        150 3000 0.07 840                                  8 120 2400 0.05 480          8 100 2000 0.06 480             8

          150 2400 0.07 670 10 120 1900 0.05 380 10 100 1600 0.06 380 10

          150 1900 0.08 610 12 120 1500 0.05 300 12 100 1300 0.06 310 12                                                                                                  RADIUS

Depth of                                                                            ap
   cut

             Precipitation hardening stainless steel,        Heat resistant alloys
 Work Cobalt chromium alloy                                  Inconel718
material

Dia.      Cutting speed Revolution Feed Feed rate Depth of cut Cutting speed Revolution Feed Feed rate Depth of cut                                                       INDEXABLE HEAD END MILLS
(mm)       (m/min) (min-1) (mm/tooth) (mm/min) ap (mm) (m/min) (min-1) (mm/tooth) (mm/min) ap (mm)

10        60 1900 0.04 300 5 30 950 0.04 150 2
12        60 1600 0.045 290 6 30 800 0.045 140 2.4
16
20        60 1200 0.05 240 8 30 600 0.05 120 3.2
25
          60 950 0.05 190 10                                 30 480 0.05            96 4
          60 760 0.05 150 12                                 30 380 0.05            76 5

Depth of                                                     ap
   cut

1)	For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective.
2)	If the depth of cut is shallow, the revolution and feed rate can be increased.
3)	The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills.

   However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur.
   In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut.

                                                       info@mitsubishitools.ru      www.mitsubishitools.ru                                                                I343