2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
TURNING INSERTS
TURNING INSERTS RECOMMENDED CUTTING CONDITIONS
y NEGATIVE INSERTS Breaker : Std : Standard Flat : Flat Top
Work Material Tensile Cutting Priority Breaker Grade Cutting Speed Feed Depth of Cut
K Strength Mode (m/min) (mm/rev) (mm)
MC5005
L1 LK MC5005 220 355 0.10 0.40 0.30 2.00
L2 MA UC5105 210 335 0.20 0.50 0.30 4.00
L3 MA MC5005 160 295 0.20 0.50 0.30 4.00
M1 MK MC5005 210 335 0.20 0.55 1.00 4.00
M2 GK UC5105 210 335 0.25 0.60 1.50 5.00
M3 Std NX2525 160 295 0.25 0.60 1.50 5.00
M4 Std MC5005 145 200 0.25 0.60 1.50 5.00
R1 RK MC5005 195 315 0.25 0.60 1.50 6.00
UC5105 195 315 0.20 0.60 2.50 6.00
R2 Flat UC5105 155 280 0.25 0.60 1.50 6.00
R3 GH 155 280 0.20 0.60 2.50 6.00
R4 Flat HTi10 95 135 0.20 0.60 2.50 6.00
R5 Flat HTi05T 105 175 0.20 0.60 2.50 6.00
R6 Flat MC5005 195 315 0.20 0.60 2.50 6.00
H1 Flat UC5105 155 280 0.20 0.60 2.50 6.00
H2 Flat MC5015 205 335 0.10 0.40 0.30 2.00
MC5015 190 305 0.20 0.50 0.30 4.00
Ductile Cast Iron < 450MPa L1 LK UC5115 155 285 0.20 0.50 0.30 4.00
(GGG40) L2 MA UC5115 155 285 0.16 0.50 0.30 4.00
L4 MA UC5115 175 315 0.10 0.50 0.30 2.50
L5 MP MC5015 190 305 0.20 0.55 1.00 4.00
L6 SW MC5015 190 305 0.25 0.60 1.50 5.00
M1 MK UC5115 155 285 0.25 0.60 1.50 5.00
M2 GK HTi10 100 140 0.25 0.60 1.50 5.00
M3 Std MC5015 180 285 0.25 0.60 1.50 6.00
M4 Std MC5015 180 285 0.20 0.60 2.50 6.00
R1 RK UC5115 150 275 0.25 0.60 1.50 6.00
R2 Flat UC5115 150 275 0.20 0.60 2.50 6.00
R3 GH MC5015 180 285 0.20 0.60 2.50 6.00
R4 Flat UC5115 150 275 0.20 0.60 2.50 6.00
H1 Flat MC5015 205 335 0.10 0.40 0.30 2.00
H2 Flat MC5015 190 305 0.20 0.50 0.30 4.00
L1 LK UC5115 165 305 0.20 0.50 0.30 4.00
L2 MA MC5015 190 305 0.20 0.55 1.50 4.00
MC5015 190 305 0.25 0.60 1.50 5.00
L3 MA UC5115 165 305 0.25 0.60 1.50 5.00
M1 MK UTi20T 85 120 0.25 0.60 1.50 5.00
M2 GK MC5015 180 285 0.25 0.60 1.50 6.00
M3 Std MC5015 180 285 0.20 0.60 2.50 6.00
M4 Std UC5115 160 290 0.25 0.60 1.50 6.00
R1 RK UC5115 160 290 0.20 0.60 2.50 6.00
R2 Flat UTi20T 80 115 0.20 0.60 2.50 6.00
MC5015 180 285 0.20 0.60 2.50 6.00
Ductile Cast Iron < 800MPa R3 GH UC5115 160 290 0.20 0.60 2.50 6.00
(GGG70) R4 Flat MC5005 195 315 0.10 0.40 0.30 2.00
R5 Flat MC5005 210 335 0.20 0.50 0.30 4.00
H1 Flat UC5105 160 295 0.20 0.50 0.30 4.00
H2 Flat
L1 LK
L2 MA
L3 MA
CUTTING CONDITIONS : : Stable Cutting : General utting : Unstable Cutting
CUTTING AREA : F : Finish Cutting L : Light Cutting M : Medium Cutting R : Rough Cutting H : Heavy Cutting
A078 info@mitsubishitools.ru www.mitsubishitools.ru