2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
RECOMMENDED CUTTING CONDITIONS
Work Material Hardness Grade Cutting Speed Finish Light Cutting LightSemi-Heavy Cutting Medium Heavy Cutting
P F7030 (m/min) Feed per Tooth (mm/tooth) Breaker Feed per Tooth (mm/tooth) Breaker Feed per Tooth (mm/tooth) Breaker
280 (210 350) 0.18 (0.08 0.28) JL 0.2 (0.1 0.3) JM 0.25 (0.1 0.35) JH
MP6120 250 (200 300) 0.2 (0.1 0.3) JM
0.2 (0.1 0.3)
Mild Steel < 180HB VP15TF 250 (200 300) 0.18 (0.08 0.28) JL 0.2 (0.1 0.3) JM 0.25 (0.1 0.35) JH
FT
VP30RT 230 (180 280) 0.18 (0.08 0.28) JL JM 0.25 (0.1 0.35) JH
NX4545 180 (130 230) 0.15 (0.07 0.23) JL 0.18 (0.1 0.28) JM
F7030 250 (200 300) 0.15 (0.07 0.23) JL 0.18 (0.1 0.28) JM 0.2 (0.1 0.3) JH
MP6120 220 (170 270) 0.18 (0.1 0.28) JM
0.18 (0.1 0.28) JM
180 280HB VP15TF 220 (170 270) 0.15 (0.07 0.23) JL 0.18 (0.1 0.28) JM 0.2 (0.1 0.3) JH
0.2 (0.1 0.3) FT
VP30RT 200 (150 250) 0.15 (0.07 0.23) JL
JH
Carbon Steel NX4545 150 (120 180) 0.13 (0.06 0.2) JL 0.15 (0.1 0.25) JM
Alloy Steel
F7030 180 (130 230) 0.13 (0.06 0.2) JL 0.15 (0.1 0.25) JM 0.18 (0.1 0.28) JH
MP6120 140 (100 180) 0.15 (0.1 0.25) JM
280 350HB VP15TF 140 (100 180) 0.13 (0.06 0.2) JL 0.15 (0.1 0.25) JM 0.18 (0.1 0.28) JH
FT
VP30RT 120 (80 160) 0.13 (0.06 0.2) JL 0.15 (0.1 0.25) JM 0.18 (0.1 0.28) JH
M < 270HB NX4545 100 (80 120) 0.1 (0.05 0.15) JL 0.13 (0.1 0.2) JM
Stainless Steel VP15TF 220 (170 270) 0.15 (0.07 0.23) JL 0.18 (0.1 0.28) JM 0.2 (0.1 0.3)
VP30RT 200 (150 250) 0.15 (0.07 0.23) JL 0.18 (0.1 0.28) JM 0.2 (0.1 0.3) JH
FT
JH
NX4545 150 (120 180) 0.15 (0.07 0.23) JL 0.18 (0.1 0.28) JM
0.2 (0.1 0.3) JM 0.25 (0.1 0.35)
K Cast Iron Tensile Strength MC5020 200 (150 250) 0.2 (0.1 0.3) JM 0.25 (0.1 0.35) JH
Ductile Cast Iron <450MPa VP15TF 180 (130 230) 0.18 (0.1 0.28) JL 0.2 (0.1 0.3) JP FT
0.3 (0.2 0.4) JH
N Aluminium Alloy HTi10 300 0.15 (0.1 0.2) JP FT
JP
S MP9120 50 (40 60) 0.15 (0.05 0.2) JM
Titanium Alloy
VP15TF 50 (40 60) 0.1 (0.05 0.2) JL 0.15 (0.05 0.2) JM ROTATING TOOLS
Heat Resistant MP9120 40 (20 50) 0.15 (0.05 0.2) JM
Alloy VP15TF 40 (20 50) 0.1 (0.05 0.2) JL 0.15 (0.05 0.2) JM
H Hardened Steel 40 55HRC VP15TF 80 (60 100) 0.08 (0.04 0.13) JL 0.1 (0.05 0.15) JM 0.12 (0.07 0.17) JH
FT
Revolution (min-1)=(1000 x Cutting Speed)u(3.14 x & D1) Table Feed (mm/min)=Feed per Tooth x Number of Teeth x Cutter Revolution
INSTRUCTIONS FOR USING INSERTS
y Instructions for use of the JP breaker y Instructions for use of wiper inserts
a The JP breaker has sharp cutting edges. a Wiper inserts for the ASX400 are
Wear gloves when handling. single-cornered.
a When machining aluminium alloy, welding to a When installing a wiper insert, place the
the cutting edge tends to occur, often leading insert so that the small chamfer is located
to insert failure. To prevent this, wet cutting is as shown.
recommended.
a The peripheral cutting edge of the wiper
insert does not protrude as far as standard
inserts. This may cause extra wear on the
insert behind the wiper.
SPARE PARTS M001
TECHNICAL DATA
N001 K029
info@mitsubishitools.ru www.mitsubishitools.ru