2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
ROTATING TOOLS
L7 D12
L8 D9
W1
10
(Max. Depth of Cut)
L1
D8
D11
D1
Right hand tool holder only.
Cutter Diameter Set Bolt Geometry
D1
y ARBOR TYPE C H :0° HSC08030H
A.R :+7° +21° T :+15°+27° &32, &40 10030H
R.R :+15° +27° I :+7°+21° &50, &63 12035H
16040H
& 80
& 100
Stock Dimensions (mm) Mass Max. *
Number of Teeth Max. Ramping Spindle
Order Number Angle Speed
R D1 L1 D9 L7 D8 D12 W1 L8 D11 (kg) %° (min-1) Clamp Wrench Anti-seize Insert
APX3000-032A05RA a 5 32 40 16 Screw Lubricant
18 9 30 8.4 5.6 14 0.2 3.1 14400 TPS25-1 TIP07F MK1KS
-040A06RA a 6 40 40 16 18 9 34 8.4 5.6 14 0.3 2.2 12800 TPS25-1 TIP07F MK1KS AOMT
-050A07RA a 7 50 40 22 20 11 45 10.4 6.3 17 0.4 1.7 11300 TPS25-1 TIP07F MK1KS 1236oo
-063A08RA a 8 63 40 22 20 11 55 10.4 6.3 17 0.7 1.3 10000 TPS25-1 TIP07F MK1KS PEER-M/H
-080A09RA a 9 80 50 27 23 13 70 12.4 7 20 1.3 1.0 8800 TPS25-1 TIP07F MK1KS AOGT
-100A11RA a 11 100 63 32 26 17 80 14.4 8 26 2.2 0.8 7800 TPS25-1 TIP07F MK1KS 1236oo
R08009CA s 9 80 50 25.4 26 13 70 9.5 6 20 1.3 1.0 8800 TPS25-1 TIP07F MK1KS PEFR-GM
R10011DA s 11 100 63 31.75 32 17 80 12.7 8 26 2.2 0.8 7800 TPS25-1 TIP07F MK1KS
(Note) When using inserts with corner radius Re>2.4, machining of the holder is required as shown on page K033.
* Clamp Torque (N • m) : TPS25-1=1.0
ROTATING TOOLS AM
Stock
Number of Teeth10(Max. Depth of Cut) A
D1L2 H1
D4L1 SECTION A-A
D5
y SCREW-IN TYPE Right hand tool holder only.
Dimensions (mm) Max. *
Ramping
Order Number
Angle
APX3000R162M08A
203M10A R D1 L1 L2 D4 D5 H1 M %° Clamp Wrench Anti-seize Insert
254M12A Screw Lubricant
325M16A
406M16A a 2 16 48 30 8.5 13 10 M8 11.3 TPS25 TIP07F MK1KS AOMT
a 3 20 53 34 10.5 18 15 M10 6.9 TPS25 TIP07F MK1KS 1236oo
a 4 25 57 35 12.5 21 17 M12 4.6 TPS25-1 TIP07F MK1KS PEER-M/H
a 5 32 61 38 17 29 22 M16 3.1 TPS25-1 TIP07F MK1KS
a 6 40 61 38 17 29 22 M16 2.2 TPS25-1 TIP07F MK1KS AOGT
1236oo
PEFR-GM
(Note 1) When using inserts with corner radius Re>2.4, machining of the holder is required as shown on page K033.
(Note 2) For screw-in type arbors, refer to page K118 K119.
* Clamp Torque (N • m) : TPS25=1.0, TPS25-1=1.0
K032 a : Inventory maintained. s : Inventory maintained in Japan. www.mitsubishitools.ru
info@mitsubishitools.ru