2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
ROTATING TOOLS Fig.1 Fig.2
L7 D12 D12
y ARBOR TYPE L8 D9 D9
15W1 W1
(Max. Depth of Cut)
L1
L7
L8
15
(Max. Depth of Cut)
L1
D8 D8
D11 D1
D1
Right hand tool holder only.
Cutter Diameter Set Bolt Geometry x
D1 z
& 40 HSC08030H
C H :0° 10030H z
A.R :+15° +22° T :+21° +28° &50, & 63 12035H x
R.R :+21° +28° I :+15° +22° & 80 16040H
& 100 *
Dimensions (mm) MBA20040H
& 125 24045H
& 160
Order Number Stock Max.
Number of Teeth Spindle
Speed
Mass
Max. Clamp Anti-seize
Ramping Angle Screw Lubricant
Type (Fig.)
R D1 L1 D9 L7 D8 D12 W1 L8 D11 (kg) %° (min-1) Wrench Insert
APX4000-040A04RA a 4 40 40 16 18 9 34
8.4 5.6 14 0.2 6 14200 1 TPS43 TIP15W MK1KS
-050A05RA a 5 50 40 22 20 11 45 10.4 6.3 17 0.3 4 12400 1 TPS43 TIP15W MK1KS
-063A06RA a 6 63 40 22 20 11 50 10.4 6.3 17 0.5 3 10800 1 TPS43 TIP15W MK1KS
-080A07RA a 7 80 50 27 23 13 AOMT
-100A08RA a 8 100 50 32 25 17
60 12.4 7 20 1.2 2 9300 1 TPS43 TIP15W MK1KS 1848oo
PEER-M/H
70 14.4 8 27 2.1 1.5 8100 1 TPS43 TIP15W MK1KS
-125A09RA a 9 125 63 40 40 56 90 16.4 9 3.3 1 7100 2 TPS43 TIP15W MK1KS
-160A10RA a 10 160 63 40 40 72 100 16.4 9 4.8 1 6100 2 TPS43 TIP15W MK1KS
(Note 1) When using inserts with corner radius Re>3.2, machining of the holder is required as shown on page K039.
(Note 2) The maximum allowable spindle speeds are set to ensure tool and insert stability.
(Note 3) When using the tool at high spindle speeds, ensure that the tool and arbor are correctly balanced.
* Clamp Torque (N • m) : TPS43=3.5
y SCREW-IN TYPE
ROTATING TOOLS AM
Stock
Coolant Hole 15(Max. Depth of Cut) A L11 H1
Number of Teeth SECTION A-A
Dimensions (mm) L2
D1L1 Right hand tool holder only.
Mass *
D4
D5
Order Number
R D1 D4 D5 L1 L2 L11 H1 M (kg) Clamp Wrench Anti-seize Insert
a u 2 25 12.5 23.5 57 Screw Lubricant
APX4000R252M12A35 35 6 19 M12 0.2 TPS4 TIP15W MK1KS
282M12A35 a u 2 28 12.5 23.5 57 35 6 19 M12 0.2 TPS4 TIP15W MK1KS
322M16A40 s u 2 32 17 28.5 63 40 6 24 M16 0.3 TPS4 TIP15W MK1KS
323M16A40 a u 3 32 17 28.5 63 40 6 24 M16 0.3 TPS4 TIP15W MK1KS AOMT
1848oo
352M16A40 s u 2 35 17 28.5 63 40 6 24 M16 0.3 TPS4 TIP15W MK1KS PEER-M/H
353M16A40 s u 3 35 17 28.5 63 40 6 24 M16 0.3 TPS4 TIP15W MK1KS
403M16A40 s u 3 40 17 28.5 63 40 6 24 M16 0.3 TPS43 TIP15W MK1KS
404M16A40 a u 4 40 17 28.5 63 40 6 24 M16 0.3 TPS43 TIP15W MK1KS
(Note 1) When using inserts with corner radius Re>3.2, machining of the holder is required as shown on page K039.
(Note 2) For screw-in type arbors, refer to page K118 K119.
* Clamp Torque (N • m) : TPS4=3.5, TPS43=3.5
a : Inventory maintained. s : Inventory maintained in Japan.
K038 info@mitsubishitools.ru www.mitsubishitools.ru