2014-Полный каталог по сверлам EN
Для заказа - info@mitsubishitools.ru
DRILLING (INDEXABLE TYPE)
TAFS,TAFM,TAFL aHigh rigidity holder.
a4 corner use insert.
aVarious grades and chip breakers.
P MK S N H
D8 (Thread hole, Coolant hole type)
DRILLING TAF DRILLS L3
L2
Stock
Number of L1
Teeth* The screw hole on the flange section is not a coolant hole.
D1 D1Number of Teeth = 4 (D1 > 49)
D4
D7Drill HoleDimensions (mm)z
Diameter Depth
Order Number Insert Number
D4 D7 D8 L1 L2 L3
D1 TAFS2700F32 x
(mm) (l/d) TAFM2700F32
TAFL2700F32 Clamp Screw Wrench
TAFS2750F32
2 TAFM2750F32 a 2 32 42 PT1/8 134 79 65 GPMT090304-Uo TS3 zTKY08F
3 TAFS2800F32
27.0 4 TAFM2800F32 a 2 32 42 PT1/8 161 106 92 GPMT090304-Uo TS3 zTKY08F
27.5 2 TAFL2800F32
28.0 3 TAFS2850F32 a 2 32 42 PT1/8 188 133 119 GPMT090304-Uo TS3 zTKY08F
28.5 2 TAFM2850F32
29.0 3 TAFL2850F40 a 2 32 42 PT1/8 134 79 65 GPMT090304-Uo TS3 zTKY08F
29.5 4 TAFS2900F32
2 TAFM2900F32 a 2 32 42 PT1/8 161 106 92 GPMT090304-Uo TS3 zTKY08F
30.0 3 TAFL2900F32
4 TAFS2950F32 a 2 32 42 PT1/8 136 81 67 GPMT11T308-Uo TS4 xTKY15D
30.5 2 TAFM2950F32
3 TAFS3000F32 a 2 32 42 PT1/8 164 109 95 GPMT11T308-Uo TS4 xTKY15D
31.0 4 TAFS3000F40
2 TAFM3000F32 a 2 32 42 PT1/8 192 137 123 GPMT11T308-Uo TS4 xTKY15D
3 TAFM3000F40
2 TAFL3000F32 a 2 32 42 PT1/8 136 81 67 GPMT11T308-Uo TS4 xTKY15D
2 TAFL3000F40
3 TAFS3050F40 a 2 32 42 PT1/8 164 109 95 GPMT11T308-Uo TS4 xTKY15D
3 TAFM3050F40
4 TAFS3100F32 a 2 40 50 PT1/8 202 137 123 GPMT11T308-Uo TS4 xTKY15D
4 TAFS3100F40
2 TAFM3100F32 a 2 32 42 PT1/8 138 83 70 GPMT11T308-Uo TS4 xTKY15D
3 TAFM3100F40
2 TAFL3100F32 a 2 32 42 PT1/8 167 112 99 GPMT11T308-Uo TS4 xTKY15D
2 TAFL3100F40
3 a 2 32 42 PT1/8 196 141 128 GPMT11T308-Uo TS4 xTKY15D
3
27.0~ 4 a 2 32 42 PT1/8 138 83 70 GPMT11T308-Uo TS4 xTKY15D
31.0 4
a 2 32 42 PT1/8 167 112 99 GPMT11T308-Uo TS4 xTKY15D
a 2 32 50 PT1/8 145 90 72 GPMT11T308-Uo TS4 xTKY15D
a 2 40 50 PT1/4 155 90 72 GPMT11T308-Uo TS4 xTKY15D
a 2 32 50 PT1/8 175 120 102 GPMT11T308-Uo TS4 xTKY15D
a 2 40 50 PT1/4 185 120 102 GPMT11T308-Uo TS4 xTKY15D
a 2 32 42 PT1/8 205 150 132 GPMT11T308-Uo TS4 xTKY15D
a 2 40 50 PT1/4 215 150 132 GPMT11T308-Uo TS4 xTKY15D
a 2 40 50 PT1/4 155 90 72 GPMT11T308-Uo TS4 xTKY15D
a 2 40 50 PT1/4 185 120 102 GPMT11T308-Uo TS4 xTKY15D
a 2 32 50 PT1/8 147 92 74 GPMT11T308-Uo TS4 xTKY15D
a 2 40 50 PT1/4 157 92 74 GPMT11T308-Uo TS4 xTKY15D
a 2 32 50 PT1/8 178 123 105 GPMT11T308-Uo TS4 xTKY15D
a 2 40 50 PT1/4 188 123 105 GPMT11T308-Uo TS4 xTKY15D
a 2 32 42 PT1/8 209 154 136 GPMT11T308-Uo TS4 xTKY15D
a 2 40 50 PT1/4 219 154 136 GPMT11T308-Uo TS4 xTKY15D
D168 a : Stock Standard info@mitsubishitools.ru
s : Stock Standard in Japan. www.mitsubishitools.ru
r : Non stock, produced to order only