2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
Diameter Insert Ramping Helical Milling (Blind Hole, Flat Bottom) Helical Milling
D1 Corner Radius
Holder (mm) Maximum Minimum Maximum Hole Maximum Minimum Maximum Minimum Maximum
Type Re Ramping Angle Distance Diameter Pitch Hole Diameter Pitch Hole Diameter Pitch
(mm) DH max. P max. DH min. P max. DH min. P max.
%° L (mm) (mm) (mm) (mm) (mm) (mm)
(mm)
20 4 17.5 47 31.5 10 31.8 10 22 1
5 16.6 71
29.5 6 31.1 7 22 1
25 4 15.1 55 41.5 10 41.4 10 32 5
5 13.7 61
39.5 9 40.6 9 32 5
28 4 14.1 59 47.5 10 47.2 10 36 6
5 13 65
45.5 9 46.4 9 36 5
32 4 12.7 66 55.5 10 55.1 10 46 9
5 12 70
53.5 9 54.3 9 46 8
35 4 10.8 78 61.5 10 61 10 50 8
5 10.2 83
59.5 9 60.2 9 50 8
B type 40 4 8.8 96 71.1 10 70.9 10 62 10
5 8.2 103
69.1 9 70.1 9 62 9
50 4 6.3 135 91.1 10 90.6 10 81 10
5 5.8 146
89.1 9 89.8 9 81 9
63 4 4.6 184 117.1 10 116.6 10 107 10
5 4.2 202
115.1 9 115.7 9 107 9
80 4 3.4 250 151.1 10 150.5 10 141 10
5 3.1 274
149.1 9 149.6 9 141 9
100 4 2.6 326 191.1 10 190.5 10 181 10
5 2.4 354
189.1 9 189.6 9 181 9
125 4 2 424 241.1 10 240.5 10 231 10
5 1.8 471
239.1 9 239.6 9 231 9
(Note) The recommended ramping feed is 0.05mm/tooth or under.
*1) Using the maximum ramping angle, the distance to reach the maximum depth of cut is as follows:
L= (maximum depth of cut ap/tan %). Maximum depth of cut A type is 15.5mm, B type is 14.8mm.
2) Corner radius of 1.2mm. For other corner radii, use the following formula. {(cutting edge diameter D1)(corner radius Re)– 0.25}2
*3) Corner radius of 2.4mm. For other corner radii, use the following formula. {(cutting edge diameter D1)(corner radius Re)– 0.25}2
**4) Corner radius of 3.2mm. For other corner radii, use the following formula. {(cutting edge diameter D1)(corner radius Re)–0.25}2
y MAX.DRILLING DEPTH ROTATING TOOLS
Type Insert Max.Drilling Depth (mm) AXD4000 can be
Corner Radius effectively used for pocket
& 20 & 25 Cutting Edge Diameter D1 & 35 &40 &125 machining without the
Re need for a prepared hole.
(mm) 5.3 5.2 &28 &32 5.3 5.3
5.3 5.2 5.3 5.3
A type 0.4 5.3 5.2 5.2 5.2 5.3 5.3
B type 0.8 4.8 4.6 5.2 5.2 4.9 4.8
1.2 4.8 4.6 5.2 5.2 4.9 4.8
1.6 4.8 4.6 4.7 4.7 4.9 4.8
2.0 4.3 3.7 4.7 4.7 4.4 4.4
2.4 4.3 3.7 4.7 4.7 4.4 4.4
3.0 3.7 2.7 4.2 4.2 3.8 3.8
3.2 3.4 2.3 4.2 4.2 3.5 3.5
3.7 3.6
4.0 3.3 3.3
5.0
info@mitsubishitools.ru www.mitsubishitools.ru K049TECHNICAL DATA N001