2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
ROTATING TOOLS
MULTI FUNCTIONAL
MILLING Including
Finishing Roughing Flat faces
AXD7000 Fig.1 D12 Fig.2 D12
D9 D9
50 W1 125 W1
L7
Light Alloy Cast Iron Carbon Steel Stainless Steel Hardened Steel 63 L8
Alloy Steel 80
ap
100 L1
L7
a Low resistance L8
inserts. ap
a Excellent wall L1
accuracy. D8 D8
a High spindle D11 D1
D1
speeds possible. Geometry
a Multi functional Right hand tool holder only. z
milling. Cutter Diameter Set Bolt x
D1
C H :0° HSC10030H z
&50, &63 12035H x
y ARBOR TYPE A.R :+11° T :+26° +29° 16040H
& 80
R.R :+26° +29° I :+11° MBA20040H
& 100
& 125
Type Stock Dimensions (mm) Mass Max. *
Insert Corner Number of Teeth Max. Allowable
Order Number Depth of Cut Revolution
Ramping Angle
Type (Fig.) Clamp Anti-seize
Re R D1 L1 D9 L7 D8 D12 W1 L8 D11 (kg) ap %° (min-1) Screw Wrench Lubricant Insert
(mm)
AXD7000-050A03RA a 3 50 50 22 20 11 45 10.4 6.3 17 0.4 21 9 30000 1 TS4SBL TKY15D MK1KS
A type0.8 -063A03RA a 3 63 50 22 20 11 50 10.4 6.3 17 0.5 21 7 25000 1 TS4SBL TKY15D MK1KS
-080A04RA a 4 80 63 27 23 13 63 12.4 7 20 1.2 21 5 23000 1 TS4SBL TKY15D MK1KS
3.2 -100A05RA a 5 100 63 32 26 17 70 14.4 8 26 1.8 21 4 19000 1 TS4SBL TKY15D MK1KS
-125B06RA a 6 125 63 40 40 56 90 16.4 9 2.7 21 3 16000 2 TS4SBL TKY15D MK1KS XDGX2270oo
AXD7000-050A03RB a 3 50 50 22 20 11 45 10.4 6.3 17 0.4 20.4 8 30000 1 TS4SBL TKY15D MK1KS PDFR-GL
B type4.0 -063A03RB a 3 63 50 22 20 11 50 10.4 6.3 17 0.5 20.4 6 25000 1 TS4SBL TKY15D MK1KS
-080A04RB a 4 80 63 27 23 13 63 12.4 7 20 1.2 20.4 4 23000 1 TS4SBL TKY15D MK1KS
5.0 -100A05RB a 5 100 63 32 26 17 70 14.4 8 26 1.8 20.4 3 19000 1 TS4SBL TKY15D MK1KS
-125B06RB a 6 125 63 40 40 56 90 16.4 9 2.7 20.4 2 16000 2 TS4SBL TKY15D MK1KS
ROTATING TOOLS (Note 1) The maximum allowable spindle speeds are set to ensure tool and insert stability.
Before operating the tool read the operational guidance on page K053.
(Note 2) When using the tool at high spindle speeds, ensure that the tool and arbor are correctly balanced.
(Note 3) Note for inserts with a corner radius of 3.0 and above, as corner radius increases the L1 dimension decreases.
* Clamp Torque (N • m) : TS4SBL=3.5
Max. D4
Dpth of Cut
Ramping Angle ap
L2
D1
L1
y SHANK TYPE Right hand tool holder only.
Type Insert Order Number Stock Dimensions (mm) Max. *
Corner R Number of Teeth Allowable
Revolution Clamp
Re AXD7000R322SA32SA a 2 Screw
0.8 D1 L1 L2 D4 ap %° (min-1) TS4SB Wrench Anti-seize Insert
(mm) TKY15D Lubricant
MK1KS
B type A type 32 170 80 32 21 19 41000
3.2 402SA40SA a 2 40 170 80 42 21 13 36000 TS4SBL TKY15D MK1KS XDGX2270oo
4.0 AXD7000R322SA32SB a 2 32 170 80 32 20.4 18 41000 TS4SB TKY15D MK1KS PDFR-GL
5.0 402SA40SB a 2 40 170 80 42 20.4 11 36000 TS4SBL TKY15D MK1KS
(Note 1) The maximum allowable spindle speeds are set to ensure tool and insert stability.
Before operating the tool read the operational guidance on page K053.
(Note 2) When using the tool at high spindle speeds, ensure that the tool and milling chuck are correctly balanced.
(Note 3) Note for inserts with a corner radius of 3.0 and above, as corner radius increases the L1 and L2 dimensions decrease.
* Clamp Torque (N • m) : TS4SB=3.5, TS4SBL=3.5
K050 a : Inventory maintained. s : Inventory maintained in Japan. www.mitsubishitools.ru
info@mitsubishitools.ru