2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
ROTATING TOOLS
RECOMMENDED CUTTING CONDITIONS
y VFX5
Work Material Cutting Number of Recommended vc n apmax ae fz vf Q Pc Expected TL
Edge (min-1) (mm) (mm) (mm/tooth) (mm/min) (cm3/min) (kW) Torque (%)
Diameter Flutes Insert (m/min)
(mm) (Nm)
S 3 LS 40 318 38 40 0.10 95 145 6.5 194 40
&40 3 MS 50 398 38 24 0.10 119 109 4.5 109 60
3 MS 60 477 38 3.5 69 80
16 0.10 143 87
3 HS 60 477 38 8 0.12 172 52 2.3 45 100
3 LS 40 255 38 50 0.10 76 145 6.5 242 40
&50 4 MS 50 318 50 30 0.10 127 191 7.9 237 60
4 MS 60 382 50 20 0.10 153 153 6.0 151 80
Titanium Alloy 4 HS 60 382 50 10 0.12 183 92 3.9 98 100
(Ti-Al-4V)
5 LS 40 202 60 63 0.10 101 382 16.8 793 40
&63 5 MS 50 253 60 38 0.10 126 286 11.8 447 60
5 MS 60 303 60 80
25 0.10 152 229 9.0 285
5 HS 60 303 60 13 0.12 182 138 5.9 185 100
6 LS 40 159 75 80 0.10 95 573 25.0 1500 40
&80 6 MS 50 199 75 48 0.10 119 430 17.6 846 60
6 MS 60 239 75 32 0.10 143 344 13.5 539 80
6 HS 60 239 75 16 0.12 172 206 8.7 350 100
3 LS 25 199 38 40 0.08 48 73 3.4 161 30
&40 3 MS 25 199 38 24 0.08 48 44 1.9 92 50
3 MS 30 239 38 16 0.10 72 44 1.8 74 70
3 HS 30 239 38 8 0.10 72 22 1.0 41 90
4 LS 25 159 50 50 0.08 51 127 5.8 350 30
&50 4 MS 25 159 50 30 0.08 51 76 3.4 201 50
4 MS 30 191 50 20 0.10 76 76 3.2 160 70
Titanium Alloy 4 HS 30 191 50 10 0.10 76 38 1.8 89 90
(Ti-5Al-5V-5Mo-3Cr)
5 LS 25 126 60 63 0.08 51 191 8.7 658 30
&63 5 MS 25 126 60 38 0.08 51 115 5.0 378 50
5 MS 30 152 60 25 0.10 76 115 4.8 301 70
ROTATING TOOLS 5 HS 30 152 60 13 0.10 76 57 2.6 167 90
6 LS 25 99 75 80 0.08 48 286 13.0 1246 30
&80 6 MS 25 99 75 48 0.08 48 172 7.5 716 50
6 32 0.10 72 172 7.1 570 70
MS 30 119 75
6 HS 30 119 75 16 0.10 72 86 3.9 316 90
*1 Please note that machining performance differs according to conditions such as the rigidity of the machinery used, workpiece clamping
rigidity, the coolant supply system pressure and flow.
*2 Internal coolant is recommended. For the tool holder, use an FMH arbor with a through coolant system. Use with external lubricating
coolant is also effective.
3 TL: Based on ae= outer diameter x 20%
**4 Maximum depth of cut, ap should be changed depending on machine rigidity and power.
K084 TECHNICAL DATA N001
info@mitsubishitools.ru www.mitsubishitools.ru