2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
RECOMMENDED CUTTING CONDITIONS (SHELL TYPE)
y CUTTING CONDITIONS FOR SHOULDER MILLING
Work Material Hardness Insert Cutting Speed Depth of Cut Width of Cut Feed per Tooth
Grade/Breaker vc ap ae fz
(m/min) (mm) (mm) (mm/tooth)
P < 180HB VP15TF 120 0.5D1 10 0.15 0.30
Mild Steel 180 350HB JM (100 140) 0.5D1 10 0.15 0.25
0.5D1 10 0.15 0.30
Carbon Steel < 300HB VP15TF 120 0.5D1 10 0.15 0.25
Alloy Steel < 200HB JM (100 140) 0.5D1 10 0.10 0.20
0.5D1 10 0.10 0.15
Alloy Tool Steel Tensile VP15TF 120 0.5D1 10 0.10 0.25
M Strength JM (80 130) 0.5D1 10 0.10 0.20
< 350MPa 0.5D1 10 0.25 0.40
Stainless Steel VP20RT 100 0.5D1 10 0.25 0.40
K JM (80 120) 0.5D1 10 0.15 0.30
0.5D1 10 0.15 0.25
Cast Iron VP15TF 100 0.5D1 10 0.20 0.35
WH (60 110) 0.5D1 10 0.20 0.35
Ductile Cast Iron Tensile 0.5D1 10 0.15 0.30
S Strength VP15TF 80 0.5D1 10 0.15 0.30
< 800MPa JM (60 100) 0.5D1 10 0.08 0.10
Ti Alloy 0.5D1 10 0.08 0.10
< 350HB VP15TF 140
WH (100 150)
VP15TF 120
JM (100 140)
VP20RT 120
JM (80 130)
100
(80 120)
120
(80 130)
100
(80 120)
100
(60 110)
80
(60 110)
100
(60 120)
80
(60 120)
45
(35 50)
40
(35 50)
(Note 1) The above cutting conditons are determined based on high rigidity machine and workpiece, where no vibration occurred.
Please adjust the machining conditions if vibration is generated.
y CUTTING CONDITIONS FOR SLOT MILLING ROTATING TOOLS
Work Material Hardness Insert Cutting Speed Depth of Cut Width of Cut Feed per Tooth
Grade/Breaker vc ap ae fz
(m/min) (mm) (mm) (mm/tooth)
P Mild Steel < 180HB VP15TF 120 10 D1 0.15 0.25
Carbon Steel 180 350HB JM (100 140) 0.25D1 D1 0.15 0.25
Alloy Steel D1 0.10 0.20
< 300HB VP15TF 100 10 D1 0.10 0.15
Alloy Tool Steel < 200HB JM (80 120) 10 D1 0.10 0.25
M Stainless Steel 0.25D1 D1 0.10 0.20
K Tensile VP15TF 80 0.6D1 D1 0.10 0.20
Strength JM (60 100) 0.25D1 D1 0.10 0.15
Cast Iron < 350MPa 0.6D1 D1 0.10 0.25
VP20RT 100 0.25D1 D1 0.10 0.20
Ductile Cast Iron Tensile JM (80 140) 0.5D1 D1 0.10 0.20
S Ti Alloy Strength 0.25D1 D1 0.10 0.15
< 800MPa VP15TF 80 0.5D1 D1 0.06 0.10
WH (60 100) 0.25D1
< 350HB
VP15TF 60
JM (50 100)
VP15TF 80
WH (60 100)
VP15TF 60
JM (50 100)
VP20RT 80
JM (60 100)
60
(50 100)
80
(60 100)
60
(50 100)
40
(35 50)
(Note 1) The above cutting conditons are determined based on high rigidity machine and workpiece, where no vibration occurred.
Please adjust the machining conditions if vibration is generated.
SPARE PARTS M001
TECHNICAL DATA
N001 K091 info@mitsubishitools.ru www.mitsubishitools.ru