2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
Work Material Tensile Cutting Priority Breaker Grade Cutting Speed Feed TURNING INSERTSDepth of Cut
K Strength Mode (m/min) (mm/rev) (mm)
Gray Cast Iron F 1 R-R/L NX2525 150 205 0.05 0.12 0.20 0.60
(GG30) 135 250 0.08 0.30 0.30 2.00
L 1 N-Flat UC5105 125 170 0.08 0.30 0.30 2.00
Ductile Cast Iron 125 170 0.08 0.30 0.30 2.00
(GGG40) L 2 N-Flat NX2525 135 250 0.08 0.30 0.30 2.00
125 170 0.08 0.30 0.30 2.00
Ductile Cast Iron L 3 R-Std NX2525 125 170 0.08 0.30 0.30 2.00
(GGG70) 150 205 0.05 0.12 0.20 0.60
M 1 N-Flat UC5105 100 145 0.05 0.12 0.20 0.60
130 245 0.08 0.30 0.30 2.00
M 2 N-Flat NX2525 130 200 0.08 0.30 0.30 2.00
130 245 0.08 0.30 0.30 2.00
M 3 R-Std NX2525 130 200 0.08 0.30 0.30 2.00
80 115 0.05 0.12 0.20 0.60
< 350MPa F 1 R-R/L NX2525 115 160 0.08 0.30 0.30 2.00
< 450MPa 115 160 0.08 0.30 0.30 2.00
< 800MPa F 2 R-R/L HTi10 140 190 0.05 0.12 0.20 0.60
130 235 0.08 0.30 0.30 2.00
L 1 N-Flat UC5115 115 160 0.08 0.30 0.30 2.00
115 160 0.08 0.30 0.30 2.00
L 2 N-Flat UE6110 130 235 0.08 0.30 0.30 2.00
115 160 0.08 0.30 0.30 2.00
M 1 N-Flat UC5115 115 160 0.08 0.30 0.30 2.00
140 190 0.05 0.12 0.20 0.60
M 2 N-Flat UE6110 95 135 0.05 0.12 0.20 0.60
125 230 0.08 0.30 0.30 2.00
F 1 R-R/L UTi20T 120 190 0.08 0.30 0.30 2.00
125 230 0.08 0.30 0.30 2.00
L 1 N-Flat VP15TF 120 190 0.08 0.30 0.30 2.00
75 110 0.05 0.12 0.20 0.60
M 1 N-Flat VP15TF 110 150 0.08 0.30 0.30 2.00
110 150 0.08 0.30 0.30 2.00
F 1 R-R/L NX2525 125 170 0.05 0.12 0.20 0.60
115 210 0.08 0.30 0.30 2.00
L 1 N-Flat UC5105 105 140 0.08 0.30 0.30 2.00
105 140 0.08 0.30 0.30 2.00
L 2 N-Flat NX2525 115 210 0.08 0.30 0.30 2.00
105 140 0.08 0.30 0.30 2.00
L 3 R-Std NX2525 105 140 0.08 0.30 0.30 2.00
125 170 0.05 0.12 0.20 0.60
M 1 N-Flat UC5105 85 120 0.05 0.12 0.20 0.60
110 205 0.08 0.30 0.30 2.00
M 2 N-Flat NX2525 105 170 0.08 0.30 0.30 2.00
110 205 0.08 0.30 0.30 2.00
M 3 R-Std NX2525 105 170 0.08 0.30 0.30 2.00
0.05 0.12 0.20 0.60
F 1 R-R/L NX2525 65 95 0.08 0.30 0.30 2.00
95 135 0.08 0.30 0.30 2.00
F 2 R-R/L HTi10 95 135
A091
L 1 N-Flat UC5115
L 2 N-Flat UE6110
M 1 N-Flat UC5115
M 2 N-Flat UE6110
F 1 R-R/L UTi20T
L 1 N-Flat VP15TF
M 1 N-Flat VP15TF
F 1 R-R/L NX2525
L 1 N-Flat UC5105
L 2 N-Flat NX2525
L 3 R-Std NX2525
M 1 N-Flat UC5105
M 2 N-Flat NX2525
M 3 R-Std NX2525
F 1 R-R/L NX2525
F 2 R-R/L HTi10
L 1 N-Flat UC5115
L 2 N-Flat UE6110
M 1 N-Flat UC5115
M 2 N-Flat UE6110
F 1 R-R/L UTi20T
L 1 N-Flat VP15TF
M 1 N-Flat VP15TF
info@mitsubishitools.ru www.mitsubishitools.ru