2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
GROOVING SYSTEM
GYSERIES (INTERNAL GROOVING)
6 90° type holder
(Note 1) For modular blades and modular holders, please order separately.
(Note 2) Please use left hand modular blade for right hand modular holder and
Insert GY2Mooooooooo--GGSM Insert GY2Gooooooooo-MF right hand modular blade for left hand modular.
Insert GY2Mooooooooo-GU Insert GY2Mooooooooo-MS
Insert GY1Gooooooooo- GF Insert GY2Mooooooooo-MM aMono block type (Air / coolant through)
GS
90° F1
&D1 ar
F2
Fig. 2
Insert GY2Mooooooooo-BM L3 H1
90° &D4
Fig. 1 L1
F1
ar
F2
L3 Right hand tool
L1 holder shown.
GROOVING Insert Hand Max. Min. Order Number
Width (R/L) Groove Depth Cutting Diameter
Seat *ar 3 D1 ID
Size W3 (mm)
(mm) (mm) Holder / Modular Holder Stock Modular Blade Stock
7 32 (6G2R9H1) GYAR25K90B-H07 a
40 (6G1R9H1) GYAR25R90B-H07 a GYM20LA-H12 a
*4.5 11.5 1 50 (6J2R3H1) GYDR32L90C-M20L a GYM20LA-H12 a
*R 6 11.5 1 60 (6J1R3H1) GYDR32S90C-M20L a GYM25LA-H14 a
*7.5 13 1 70 (6L2R3H1) GYDR40M90D-M20L a GYM25LA-H14 a
7.5 13 1 (6L1R3H1) GYDR40T90D-M20L a
*4.75 32 (6L2R4H1) GYDR40M90D-M25L a
40 (6L1R4H1) GYDR40T90D-M25L a GYM20RA-H12
50 (6N2R4H1) GYDR50P90F-M25L a GYM20RA-H12 a
60 (6N1R4H1) GYDR50T90F-M25L a GYM25RA-H14 a
70 GYM25RA-H14 a
H 5.00 7 (6G2L9H1) GYAL25K90B-H07 a a
5.24 (6G1L9H1) GYAL25R90B-H07 a
(6J2L3H1) GYDL32L90C-M20R a
*4.5 11.5 1 (6J1L3H1) GYDL32S90C-M20R a
*L 6 11.5 1 (6L2L3H1) GYDL40M90D-M20R a
(6L1L3H1) GYDL40T90D-M20R a
*7.5 13 1 (6L2L4H1) GYDL40M90D-M25R a
*7.5 13 1 (6L1L4H1) GYDL40T90D-M25R a
(6N2L4H1) GYDL50P90F-M25R a
(6N1L4H1) GYDL50T90F-M25R a
7.5 13 *1 60 (6L2R4J1) GYDR40M90D-M25L a GYM25LA-J14 a
7.5 13 *1 70 (6L1R4J1) GYDR40T90D-M25L a GYM25LA-J14 a
(6N2R4J1) GYDR50P90F-M25L a
(6N1R4J1) GYDR50T90F-M25L a
R
6.00 7.5 13 *1 60 (6L2L4J1) GYDL40M90D-M25R a GYM25RA-J14 a
J 6.31 7.5 13 *1 70 (6L1L4J1) GYDL40T90D-M25R a GYM25RA-J14 a
(6N2L4J1) GYDL50P90F-M25R a
6.35 (6N1L4J1) GYDL50T90F-M25R a
L
1 The maximum groove depth varies according to the cutting diameter D1. For details, please refer to page F119.
*2 Dimensions shown are when the gauge insert is used. If other insert geometries are used then L1, L3, F1 and F2 values may vary.
**3 The maximum groove depth (ar) is a value within the dimension L3.
a : Inventory maintained.
F116 info@mitsubishitools.ru www.mitsubishitools.ru