2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
VQ END MILLS
CARBIDE VQMHZV
End mill, Medium cut length, 3 flute for plunging and slotting
y Shoulder milling
When machine and work material rigidity and chip discharge properties are sufficient, please select the high efficiency cutting conditions.
When machine rigidity, work material rigidity or chip discharge properties are insufficient, please select general-purpose cutting conditions.
High efficiency cutting conditions
Copper, Copper alloy Heat resistant alloys
Work
material
Inconel718
Dia. Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut
(mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm)
1 120 38000 860 1.5 0.2 40 13000 160 1.5 0.05
1.5 150 32000 1400 2.2 0.3 40 8500 170 2.2 0.08
2 180 29000 2200 3 0.6 40 6400 170 3 0.2
3 180 19000 2300 4.5 0.9 40 4200 180 4.5 0.3
4 180 14000 2300 6 1.2 40 3200 180 6 0.4
5 180 11000 2100 7.5 1.5 40 2500 180 7.5 0.5
6 180 9500 2300 9 1.8 40 2100 190 9 0.6
8 180 7200 2300 12 2.4 40 1600 190 12 0.8
10 180 5700 2100 15 3 40 1300 220 15 1
12 180 4800 1700 18 3.6 40 1100 210 18 1.2
16 180 3600 1500 24 4.8 40 800 150 24 1.6
20 180 2900 1200 30 6 40 640 120 30 2
SOLID END MILLS ae
Depth of ap
cut
General purpose cutting conditions
Copper, Copper alloy Heat resistant alloys
Work
material
Inconel718
Dia. Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut
(mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm)
1 120 38000 560 1.5 0.2 30 9500 75 1.5 0.05
1.5 140 30000 890 2.2 0.3 30 6400 82 2.2 0.07
2 140 22000 1100 3 0.6 30 4800 86 3 0.2
3 140 15000 1200 4.5 0.9 30 3200 89 4.5 0.3
4 140 11000 1200 6 1.2 30 2400 90 6 0.4
5 140 8900 1100 7.5 1.5 30 1900 90 7.5 0.5
6 140 7400 1200 9 1.8 30 1600 95 9 0.6
8 140 5600 1200 12 2.4 30 1200 95 12 0.8
10 140 4500 1100 15 3 30 950 110 15 1
12 140 3700 880 18 3.6 30 800 100 18 1.2
16 140 2800 750 24 4.8 30 600 76 24 1.6
20 140 2200 590 30 6 30 480 61 30 2
ae
Depth of ap
cut
1) VQ coating is less electro conductive; therefore an external contact type (electric transmitted) tool setter may not work.
When measuring the tool length, please use an internal contact type (non-electricity type) tool setter or a laser type tool setter.
2) Effective cutting of stainless steel, titanium alloys and heat-resistant alloys etc. can be achieved with the use of emulsion.
3) Chattering can still occur if the machine rigidity and clamping method are insufficient.
In these cases the feed and speed should be reduced proportionately.
4) When the depth of cut is smaller than shown the revolution and feed rate can be increased.
I214 info@mitsubishitools.ru www.mitsubishitools.ru
