2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
TURNING INSERTS
TURNING INSERTS RECOMMENDED CUTTING CONDITIONS
y NEGATIVE INSERTS Breaker : Std : Standard Flat : Flat Top
Work Material Hardness Cutting Priority Breaker Grade Cutting Speed Feed Depth of Cut
P Mode (m/min) (mm/rev) (mm)
VP25N
F1 FY NX2525 285 445 0.09 0.23 0.20 0.80
F2 FS VP25N 270 385 0.09 0.23 0.20 0.70
L1 SY MP3025 260 405 0.16 0.33 0.50 1.20
NX3035 275 420 0.09 0.23 0.20 0.80
Mild Steel < 180HB F1 FY NX2525 260 370 0.09 0.23 0.20 0.80
(St37-2, Ck10) F2 FY MP3025 270 385 0.09 0.23 0.20 0.70
F3 FS NX3035 250 385 0.16 0.33 0.50 1.20
L1 SY UE6020 235 335 0.16 0.33 0.50 1.20
L2 SY UE6020 285 460 0.09 0.23 0.20 0.80
F1 FY UE6020 285 460 0.09 0.23 0.20 0.70
F2 FS AP25N 260 420 0.16 0.33 0.50 1.20
L1 SY NX2525 215 340 0.08 0.20 0.20 1.00
MP3025 205 295 0.08 0.20 0.20 1.00
F1 FH NX2525 210 325 0.05 0.15 0.10 0.50
UE6105 195 280 0.10 0.30 0.20 1.00
F2 FH UE6105 220 405 0.10 0.40 0.30 2.00
MP3025 220 405 0.10 0.40 0.30 2.00
F 3 R/L-F AP25N 195 295 0.10 0.40 0.30 2.00
NX2525 200 315 0.10 0.40 0.30 2.00
F4 PK UE6105 190 270 0.10 0.40 0.30 2.00
UE6105 220 405 0.10 0.40 0.30 2.00
L1 LP MP3025 220 405 0.10 0.50 0.30 2.50
NX2525 195 295 0.10 0.50 0.30 2.50
L2 SH MP3025 190 270 0.10 0.50 0.30 2.50
UE6105 195 295 0.08 0.20 0.30 1.20
L3 LP MP3025 200 370 0.16 0.50 0.30 4.00
UE6105 175 270 0.16 0.50 0.30 4.00
L4 SH UE6105 200 370 0.20 0.50 0.30 4.00
UE6105 200 370 0.20 0.55 1.00 4.00
L5 SH MP3025 200 370 0.25 0.60 1.50 5.00
NX2525 175 270 0.25 0.60 1.50 5.00
L6 SA UTi20T 170 245 0.25 0.60 1.50 5.00
UE6105 85 125 0.25 0.60 1.50 5.00
L7 SW MP3025 200 370 0.20 0.60 0.90 4.00
UE6105 175 270 0.15 0.32 0.40 2.00
L8 SW UE6105 190 350 0.25 0.60 1.50 6.00
UE6110 190 350 0.25 0.60 1.50 6.00
L9 SW UE6110 160 275 0.50 1.26 3.00 11.00
MP3025 135 225 0.70 1.30 4.00 12.00
L 10 R/L-K NX3035 210 325 0.08 0.20 0.20 1.00
UE6110 200 285 0.08 0.20 0.20 1.00
M1 MP UE6110 230 390 0.08 0.20 0.20 1.00
UE6110 210 355 0.10 0.40 0.30 2.00
M2 MP UE6110 210 355 0.10 0.40 0.30 2.00
MP3025 210 355 0.10 0.40 0.30 2.00
Carbon Steel • 180 M3 MA NX3035 195 295 0.10 0.40 0.30 2.00
Alloy Steel | M4 MH 185 260 0.10 0.40 0.30 2.00
M5 Std
(Ck45, 42CrMo4) 280HB M6 Std
M7 Std
M8 Std
M9 MW
M 10 R/L
R1 RP
R2 GH
H1 HX
H2 HV
F1 FH
F2 FH
F3 FH
L1 LP
L2 SH
L3 SA
L4 LP
L5 SH
CUTTING CONDITIONS : : Stable Cutting : General Cutting : Unstable Cutting
CUTTING AREA : F : Finish Cutting L : Light Cutting M : Medium Cutting R : Rough Cutting H : Heavy Cutting
A070 info@mitsubishitools.ru www.mitsubishitools.ru