2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
для заказа - info@mitsubishitools.ru
RECOMMENDED CUTTING CONDITIONS
Work Material Hardness Grade Cutting Speed FinishLight Cutting LightSemi-Heavy Cutting MediumHeavy Cutting
P < 180HB (m/min) Feed per Tooth (mm/tooth) Breaker Feed per Tooth (mm/tooth) Breaker Feed per Tooth (mm/tooth) Breaker
F7030
Mild Steel MP6120 280 (210 350) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
VP15FT
MP6130 250 (200 300) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
240 (190 290) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
VP30RT 230 (180 280) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
NX4545 180 (130 230) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM
180 280HB F7030 250 (200 300) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
MP6120 220 (170 270) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
VP15FT 200 (150 230) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
MP6130
VP30RT 150 (120 180) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
Carbon Steel NX4545 150 (120 180) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM
Alloy Steel
F7030 180 (130 230) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
MP6120
VP15FT 140 (100 180) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
MP6130
280 350HB 120 (90 150) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
VP30RT 100 (80 160) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
NX4545 100 (80 160) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM
MP7130
M VP15FT 220 (170 270) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
Stainless Steel MP7140
< 270HB VP30FT 200 (150 250) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
NX4545
MC5020 150 (120 180) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM
VP15TF
K Tensile Strength MC5020 200 (150 250) 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
FT
Cast Iron < 450MPa HTi10
Ductile Cast Iron 180 (130 250) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
Tensile Strength 110 (80 150) 0.2 (0.1 0.3) JM 0.3 (0.2 0.4) JH
FT
> 450MPa
N 650 (300 1000) 0.15 (0.10.2) JP 0.2 (0.1 0.3) JP 0.3 (0.2 0.4) JP
Aluminium Alloy
ROTATING TOOLS
S MP9120 50 (40 60) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM
Titanium Alloy VP15FT 45 (30 55) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM
MP9130 40 (20 50) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM
Heat Resistant Alloy MP9120 35 (15 45) 0.15 (0.10.2) JL 0.2 (0.1 0.3) JM
(Inconel718 etc.) VP15FT
MP9130
H 40 55HRC 80 (60 100) 0.1 (0.050.15) JL 0.15 (0.1 0.2) JM 0.2 (0.1 0.3) JH
Hardened Steel VP15TF
a Revolution (min-1)=(1000Cutting Speed)(3.14&D1) a Table Feed (mm/min)=Feed per ToothNumber of TeethCutter Revolution
SPARE PARTS M001
TECHNICAL DATA
N001 K013
info@mitsubishitools.ru www.mitsubishitools.ru