2014-2015 Полный каталог инструмента Mitsubishi (Митсубиси) EN
CARBIDE для заказа - info@mitsubishitools.ru
MS PLUS END MILLS
MP2XLB
Ball nose, Short cut length, 2 flute, Long neck
Carbon steel, Alloy steel, Hardened steel (4055HRC) Copper, Copper alloys
Alloy tool steel, Prehardened steel,
Work material Precipitation hardening stainless steel
R Neck length Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
(min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm)
(mm) (mm)
40000 4000 0.05 40000 3200 0.05 40000 3200 0.1
SOLID END MILLS R0.5 3 40000 4000 0.05 40000 3200 0.05 40000 3200 0.1
4 35000 3000 0.03 35000 2400 0.03 35000 2400 0.06
R0.6 6 30000 2000 0.02 30000 1600 0.02 30000 1600 0.04
R0.7 8 20000 1000 0.01 20000 0.01 20000 0.02
R0.75 10 20000 1000 0.01 20000 800 0.01 20000 800 0.02
R0.8 12 18000 0.008 18000 800 0.008 18000 800 0.016
R0.9 14 18000 600 0.008 18000 480 0.008 18000 480 0.016
16 13000 500 0.005 13000 400 0.005 13000 400 0.01
R1 18 13000 300 0.005 13000 240 0.005 13000 240 0.01
20 40000 250 40000 200 40000 200
6 40000 0.04 40000 0.04 40000 0.08
8 27000 4400 0.04 27000 3500 0.04 27000 3500 0.08
10 16000 4000 0.02 16000 3200 0.02 16000 3200 0.04
12 15000 1900 0.02 15000 1500 0.02 15000 1500 0.04
18 11000 1400 0.008 11000 1100 0.008 11000 1100 0.016
24 40000 0.006 40000 0.006 40000 0.012
8 26000 700 26000 560 26000 560
12 17000 300 0.05 17000 240 0.05 17000 240 0.1
16 40000 0.04 36000 0.04 36000 0.08
6 40000 4000 0.03 36000 3200 0.03 36000 2560 0.06
8 40000 2000 36000 1600 36000 1280
10 32000 1400 0.07 29000 1120 0.07 29000 0.14
12 15000 0.07 15000 0.07 15000 896 0.14
16 12000 6000 0.06 12000 4300 0.06 12000 0.12
20 6000 0.04 4300 0.04 4300 0.08
30 9000 5000 0.03 9000 3600 0.03 9000 4300 0.06
8 40000 3400 0.02 32000 2400 0.02 32000 3600 0.04
12 36000 1400 0.01 29000 1100 0.01 29000 2400 0.02
16 14000 14000 14000 1100
20 12000 900 0.08 12000 720 0.08 12000 0.16
8 40000 400 0.06 32000 320 0.06 32000 720 0.12
12 40000 0.04 32000 0.04 32000 320 0.08
16 28000 6000 0.03 22000 3800 0.03 22000 0.06
20 10000 4500 10000 2800 10000 3800
4 40000 1400 0.09 32000 1100 0.09 32000 2800 0.18
6 40000 1000 0.07 32000 0.07 32000 1100 0.14
8 40000 0.04 32000 800 0.04 32000 0.08
10 40000 6600 0.03 32000 0.03 32000 800 0.06
12 40000 5000 32000 4200 32000
16 32000 2800 0.1 26000 3200 0.1 26000 4200 0.2
20 10000 0.1 10000 1800 0.1 10000 3200 0.2
25 10000 800 0.1 10000 0.1 10000 1800 0.2
30 10000 0.08 10000 640 0.08 10000 0.16
35 10000 8000 0.08 10000 0.08 10000 640 0.16
40 8000 0.05 5000 0.05 0.1
8000 6000 0.04 8000 5000 0.04 8000 5000 0.08
5000 0.04 3800 0.04 5000 0.08
5000 0.02 3200 0.02 3800 0.04
3500 0.02 3200 0.02 3200 0.04
1000 0.01 2200 0.01 3200 0.02
1000 2200
800
800 800 800
600 640 800
400 480 640
320 480
320
Depth ofcut <0.1R (R <1)
<0.2R (R > 1)
ap
R:Radius
6) For hardened steel over 55HRC, use VF-2XLB.
7) For cutting conditions for austenitic stainless steel and titanium alloy, use the high hardness steel (45-55HRC) table but reduce the spindle
speed by 40% and the feed rate by 55%.
I144 info@mitsubishitools.ru www.mitsubishitools.ru